ASTM G190-15
Standard Guide for Developing and Selecting Wear Tests

Standard No.

ASTM G190-15

Release Date

2015

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM G190-15

Scope

5.1 The guidance and methodology provided by this guide is applicable for any wear situation and is not limited to material or lubrication. This guide is intended to provide general information and guidance regarding the selection and development of a wear test and does not provide specifics about any one wear test or intended application. In general the variability and correlation that is obtained with any wear test is determined by the degree to which the various elements of the wear test methodology described in this guide are followed.

1.1 This guide covers general information for the development and selection of a wear test for an intended application.

ASTM G190-15 Referenced Document

• ASTM D2266 Standard Test Method for Wear Preventive Characteristics of Lubricating Grease (Four-Ball Method)
• ASTM D2670 Standard Test Method for Measuring Wear Properties of Fluid Lubricants (Falex Pin and Vee Block Method)
• ASTM D2714 Standard Test Method for Calibration and Operation of the Falex Block-on-Ring Friction and Wear Testing Machine
• ASTM D3702 Standard Test Method for Wear Rate and Coefficient of Friction of Materials in Self-Lubricated Rubbing Contact Using a Thrust Washer Testing Machine
• ASTM D3704 Standard Test Method for Wear Preventive Properties of Lubricating Greases Using the (Falex) Block on Ring Test Machine in Oscillating Motion
• ASTM D4170 Standard Test Method for Fretting Wear Protection by Lubricating Greases
• ASTM D4172 Standard Test Method for Wear Preventive Characteristics of Lubricating Fluid (Four-Ball Method)
• ASTM F732 Standard Test Method for Wear Testing of Polymeric Materials Used in Total Joint Prostheses
• ASTM G105 Standard Test Method for Conducting Wet Sand/Rubber Wheel Abrasion Tests
• ASTM G117 Standard Guide for Calculating and Reporting Measures of Precision Using Data from Interlaboratory Wear or Erosion Tests
• ASTM G118 Standard Guide for Recommended Format of Wear Test Data Suitable for Databases
• ASTM G119 Standard Guide for Determining Synergism Between Wear and Corrosion
• ASTM G132 Standard Test Method for Pin Abrasion Testing
• ASTM G133 Standard Test Method for Linearly Reciprocating Ball-on-Flat Sliding Wear
• ASTM G134 Standard Test Method for Erosion of Solid Materials by a Cavitating Liquid Jet
• ASTM G137 Standard Test Method for Ranking Resistance of Plastic Materials to Sliding Wear Using a Block-On-Ring Configuration
• ASTM G163 Standard Guide for Digital Data Acquisition in Wear and Friction Measurements
• ASTM G171 Standard Test Method for Scratch Hardness of Materials Using a Diamond Stylus
• ASTM G174 Standard Test Method for Measuring Abrasion Resistance of Materials by Abrasive Loop Contact
• ASTM G176 Standard Test Method for Ranking Resistance of Plastics to Sliding Wear Using Block-on-Ring Wear Test—Cumulative Wear Method
• ASTM G181 Standard Test Method for Conducting Friction Tests of Piston Ring and Cylinder Liner Materials Under Lubricated Conditions
• ASTM G32 Standard Test Method for Cavitation Erosion Using Vibratory Apparatus
• ASTM G40 Standard Terminology Relating to Wear and Erosion
• ASTM G56 Standard Test Method for Abrasiveness of Ink-Impregnated Fabric Printer Ribbons
• ASTM G65 Standard Test Method for Measuring Abrasion Using the Dry Sand/Rubber Wheel Apparatus
• ASTM G73 Standard Practice for Liquid Impingement Erosion Testing
• ASTM G75 Standard Test Method for Determination of Slurry Abrasivity (Miller Number) and Slurry Abrasion Response of Materials (SAR Number)
• ASTM G76 Standard Test Method for Conducting Erosion Tests by Solid Particle Impingement Using Gas Jets
• ASTM G77 Standard Test Method for Ranking Resistance of Materials to Sliding Wear Using Block-on-Ring Wear Test
• ASTM G81 Standard Test Method for Jaw Crusher Gouging Abrasion Test
• ASTM G83 Standard Test Method for Wear Testing with a Crossed-Cylinder Apparatus
• ASTM G98 Standard Test Method for Galling Resistance of Materials
• ASTM G99 Standard Test Method for Wear Testing with a Pin-on-Disk Apparatus

ASTM G190-15 history

• 2015 ASTM G190-15 Standard Guide for Developing and Selecting Wear Tests
• 2006 ASTM G190-06 Standard Guide for Developing and Selecting Wear Tests