This part of GB/T 27748 specifies the operational performance and environmental impact of stationary fuel cell power generation systems (hereinafter referred to as power generation systems). This section applies to the following test methods: - power output under specified operating conditions and transient conditions; - power generation efficiency and thermal efficiency under specified operating conditions; - environmental characteristics: for example, under specified operating conditions and transient conditions Gas emissions, noise, etc. under variable working conditions; - This standard does not provide electromagnetic compatibility (EMC) tests. This section does not apply to small stationary polymer fuel cell power generation systems with an output power of less than 10 kW. IEC 62282-3-201, which has not yet been issued, is applicable to this type of system. Due to the different types and applications of fuel cells, as well as the different forms of input and output fluid substances and energy, the power generation system can have different subsystems. However, in order to evaluate the power generation system, this section defines a general system diagram and boundaries (see Figure 1). To determine the test boundary for power generation systems, the following conditions are considered: - all energy recovery systems are included within the test boundary; - any type of electrical energy storage device is considered outside the test boundary; - input fuel (such as natural gas , propane gas, pure hydrogen, etc.) is calculated based on its state at the boundary of the power generation system.
GB/T 27748.2-2013 Referenced Document
GB/T 10894-2004 Determination method of noise emitted by separating machine
GB/T 13850-1998 Electrical measuring transducers for converting a.c electrical quantities to analogue or digital singals
GB/T 17215.211-2006 Electricity metering equipment (a.c.) - General requirements, tests and test conditions - Part 11: Metering equipment
GB/T 17215.322-2008 Electricity metering equipment (a.c.).Particular requirement.Part 22:Static meters for active energy(classes 0.2S and 0.5S)
GB/T 17626.13-2006 Electromagnetic compatibility Testing and measurement techniques Harmonics and interharmonics including mains signalling at a.c. power port, low frequency immunity test
GB/T 17626.7-2008 Electromagnetic compatibility.Testing and measurement techniques.General guide on harmonics and interharmonics measurements and instrumentation,for power supply systems and equipment connected thereto
GB/T 17860.1 Electrical measuring instruments--X-t recorders Part 1: Definitions and requirements
GB/T 17860.2 Electrical measuring instruments--X-t recorders. Part 2: Recommended additional test methods
GB/T 2429-1988 Aviation fuels--Calculation of net heat of combustion
GB/T 262 Petroleum products and hydrocarbon solvents.Determination of aniline point and mixed aniline point
GB/T 3767-1996 Acoustics--Determination of sound power levels of noise sources using sound pressure--Engineering method in an essentially free field over a reflecting plane
GB/T 7676.1 Direct acting indicating analogue electrical measuring instruments and their accessories.Part 1:Definitions and general requirements common to all parts*, 2017-09-07 Update
GB/T 7676.2 Direct acting indicating analogue electrical measuring instruments and their accessories—Part 2:Special requirements for ammeters and voltmeters*, 2017-09-07 Update
GB/T 7676.3 Direct acting indicating analogue electrical measuring instruments and their accessories—Part 3:Special requirements for wattmeters and varmeters*, 2017-09-07 Update
GB/T 7676.4 Direct acting indicating analogue electrical measuring instruments and their accessories—Part 4:Special requirements for frequency meters*, 2017-09-07 Update
GB/T 7676.5 Direct acting indicating analogue electrical measuring instruments and their accessories—Part 5:Special requirements for phase meters, power factor meters and synchroscopes*, 2017-09-07 Update
GB/T 7676.6 Direct acting indicating analogue electrical measuring instruments and their accessories—Part 6:Special requirements for ohmmeters(impedance meters ) and conductance meters*, 2017-09-07 Update
GB/T 7676.7 Direct acting indicating analogue electrical measuring instruments and their accessories—Part 7:Special requirements for multi-function instruments*, 2017-09-07 Update
GB/T 7676.8 Direct acting indicating analogue electrical measuring instruments and their accessories—Part 8:Special requirements for accessories*, 2017-09-07 Update
GB/T 7676.9 Direct acting indicating analogue electrical measuring instruments and their accessories—Part 9:Recommended test methods*, 2017-09-07 Update
IEC 60359 Electrical and electronic measurement equipment - Expression of performance