ASTM F2905/F2905M-13
Standard Specification for Black Crosslinked Polyethylene (PEX) Line Pipe, Fittings and Joints For Oil and Gas Producing Applications
- Standard No.
- ASTM F2905/F2905M-13
- Release Date
- 2013
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM F2905/F2905M-19
- Latest
- ASTM F2905/F2905M-22
- Scope
1.1 This specification covers outside diameter controlled, pressure rated, black metric-sized and IPS-sized crosslinked polyethylene (PEX) pipe, fittings and joints, made in pipe dimension ratios ranging from 6 to 17. Included are requirements and test methods for material, workmanship, dimensions, burst pressure, hydrostatic sustained pressure, stabilizer functionality, bent-pipe hydrostatic pressure, degree of crosslinking, and chemical resistance. Requirements for pipe and fittings markings are also given. The pipe, fittings and joints covered by this specification are intended for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, gas gathering, multiphase fluids, and non-potable oilfield water. This specification does not cover pipe for gas distribution applications.
1.2 The text of this specification references notes, footnotes, and appendixes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Note 1—Metric sized (SI units) pipe should only be joined with corresponding metric sized fittings, and inch sized pipe should only be joined with corresponding inch sized fittings. Inch sized fittings should not be used for metric sized pipe, and metric sized fittings should not be used for IPS inch sized pipe.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM F2905/F2905M-13 Referenced Document
- ASTM D1505 Standard Test Method for Density of Plastics by the Density-Gradient Technique
- ASTM D1598 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
- ASTM D1599 Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings
- ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
- ASTM D1603 Standard Test Method for Carbon Black In Olefin Plastics
- ASTM D2122 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
- ASTM D2290 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
- ASTM D2765 Standard Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics
- ASTM D2837 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
- ASTM D4218 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique
- ASTM D618 Standard Practice for Conditioning Plastics for Testing
- ASTM D792 Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
- ASTM F1055 Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene Pipe and Tubing
- ASTM F1948 Standard Specification for Metallic Mechanical Fittings for Use on Outside Diameter Controlled Thermoplastic Gas Distribution Pipe and Tubing
- ASTM F2619/F2619M Standard Specification for High-Density Polyethylene (PE) Line Pipe
- ASTM F412 Standard Terminology Relating to Plastic Piping Systems
- ISO 1167 Thermoplastics pipes for the conveyance of fluids - Resistance to internal pressure - Test method; Technical Corrigendum 1
- ISO 14531-2 Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Part 2: Fittings for heat-fusion jointing
- ISO 14531-3 Plastics pipes and fittings - Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels - Metric series - Specifications - Part 3: Fittings for mechanical jointing (including PE-X/metal transitions)
ASTM F2905/F2905M-13 history
- 2022 ASTM F2905/F2905M-22 Standard Specification for Crosslinked Polyethylene (PEX) Line Pipe For Oil and Gas Producing Applications
- 2021 ASTM F2905/F2905M-21a Standard Specification for Crosslinked Polyethylene (PEX) Line Pipe For Oil and Gas Producing Applications
- 2021 ASTM F2905/F2905M-21 Standard Specification for Crosslinked Polyethylene (PEX) Line Pipe For Oil and Gas Producing Applications
- 2020 ASTM F2905/F2905M-20a Standard Specification for Crosslinked Polyethylene (PEX) Line Pipe For Oil and Gas Producing Applications
- 2020 ASTM F2905/F2905M-20 Standard Specification for Crosslinked Polyethylene (PEX) Line Pipe For Oil and Gas Producing Applications
- 2019 ASTM F2905/F2905M-19 Standard Specification for Crosslinked Polyethylene (PEX) Line Pipe For Oil and Gas Producing Applications
- 2013 ASTM F2905/F2905M-13 Standard Specification for Black Crosslinked Polyethylene (PEX) Line Pipe, Fittings and Joints For Oil and Gas Producing Applications
