ASTM F2468-05(2011)
Standard Classification for Specifying Silicone Adhesives and Sealants for Transportation Applications
- Standard No.
- ASTM F2468-05(2011)
- Release Date
- 2005
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM F2468-05(2019)
- Latest
- ASTM F2468-05(2019)
- Scope
The purpose of this classification system is to provide a method of adequately identifying silicone adhesives and sealants through the use of a line call-out designation.
This classification system was designed to permit the addition of property values for future silicone adhesives and sealants.
1.1 This classification covers silicone adhesives and sealants intended for but not limited to sealing and retaining metallic and nonmetallic component assemblies in transportation applications. The materials cure to an elastomeric state by their specified cure system and mechanism.
Note 18212;The classification system may serve many of the needs of industries using silicone materials. This classification is subject to revision, as the need requires; therefore, the latest revision should always be used.
1.2 This classification is intended to be a means of classifying silicone materials. It is not intended for engineering design purposes.
1.3 It is not the intent of this classification to include pressure-sensitive or hot-melt adhesives.
1.4 In all cases in which the provisions of this classification system would conflict with the referenced ASTM standard for a particular method, the latter shall take precedence.
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.6 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this classification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM F2468-05(2011) Referenced Document
- ASTM C679 Standard Test Method for Tack-Free Time of Elastomeric Sealants
- ASTM D1002 Standard Test Method for Apparent Shear Strength of Single-Lap-Joint Adhesively Bonded Metal Specimens by Tension Loading (Metal-to-Metal)
- ASTM D1053 Standard Test Methods for Rubber Property—Stiffening at Low Temperatures: Flexible Polymers and Coated Fabrics
- ASTM D1084 Standard Test Methods for Viscosity of Adhesives
- ASTM D1349 Standard Practice for Rubber-Standard Temperatures for Testing
- ASTM D1415 Standard Test Method for Rubber Property—International Hardness
- ASTM D149 Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
- ASTM D150 Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation
- ASTM D1566 Standard Terminology Relating to Rubber
- ASTM D1898
- ASTM D2240 Standard Test Method for Properties of Rubber &8212; Durometer Hardness*， 2024-04-19 Update
- ASTM D257 Standard Test Methods for DC Resistance or Conductance of Insulating Materials
- ASTM D3182 Standard Practice for Rubber-Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets
- ASTM D412 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers8212;Tension
- ASTM D471 Standard Test Method for Rubber Property-Effect of Liquids
- ASTM D4800 Standard Guide for Classifying and Specifying Adhesives
- ASTM D573 Standard Test Method for Rubber-Deterioration in an Air Oven
- ASTM D618 Standard Practice for Conditioning Plastics for Testing
- ASTM D624 Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
- ASTM D792 Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
- ASTM D907 Standard Terminology of Adhesives
- SAE J369 FLAMMABILITY OF AUTOMOTIVE INTERIOR MATERIALS - HORIZONTAL TEST METHOD
ASTM F2468-05(2011) history
- 2019 ASTM F2468-05(2019) Standard Classification for Specifying Silicone Adhesives and Sealants for Transportation Applications
- 2005 ASTM F2468-05(2011) Standard Classification for Specifying Silicone Adhesives and Sealants for Transportation Applications
- 2005 ASTM F2468-05 Standard Classification for Specifying Silicone Adhesives and Sealants for Transportation Applications
