ASTM D3307-04
Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials
- Standard No.
- ASTM D3307-04
- Release Date
- 2004
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D3307-06
- Latest
- ASTM D3307-21
- Scope
1.1 This specification covers melt processable molding and extrusion materials of PFA-perfluoro(alkoxy alkane) fluorocarbon resin. The materials are copolymers of TFE-fluorocarbon resins containing perfluoroalkoxy side chains. These materials were formerly the subject of this specification and Specification D 6314.
1.2 This specification is intended to provide a means for calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the plastics field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this specification.
1.3 This specification does not cover recycled plastics.
1.4 The tests involved are intended to provide information for identifying the materials covered. It is not the function of this specification to provide engineering data for design purposes. Specimens prepared by injection molding or extrusion could yield test results that may vary from the values in this specification.
1.5 The values stated in SI units are to be regarded as the standard. The values given in brackets are for information only.
1.6 The following precautionary caveat pertains only to the test methods portions, Sections and of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 18212;This specification, ISO 12086-1(1995), and ISO 12086-2(1995) differ in approach or detail. Data obtained using either may not be technically equivalent.
ASTM D3307-04 Referenced Document
- ASTM D1238 Standard Test Method for Flow Rates of Thermoplastics by Extrusion Plastometer
- ASTM D150 Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation
- ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
- ASTM D2116 Standard Specification for FEP-Fluorocarbon Molding and Extrusion Materials
- ASTM D3892 Standard Practice for Packaging/Packing of Plastics
- ASTM D4591 Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry
- ASTM D4895 Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion
- ASTM D5033 Standard Guide for Development of ASTM Standards Relating to Recycling and Use of Recycled Plastics
- ASTM D618 Standard Practice for Conditioning Plastics for Testing
- ASTM D6314 Standard Specification for Fluorocarbon Perfluoromethoxy (MFA) Resin Molding and Extrusion Materials
- ASTM D638 Standard Test Method for Tensile Properties of Plastics
- ASTM D792 Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
- ASTM D883 Standard Terminology Relating to Plastics
- ASTM E177 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
- IEEE/ASTM SI 10 American National Standard for Metric Practice
ASTM D3307-04 history
- 2021 ASTM D3307-21 Standard Specification for Perfluoroalkoxy (PFA) Resin Molding and Extrusion Materials
- 2016 ASTM D3307-16 Standard Specification for Perfluoroalkoxy (PFA) Resin Molding and Extrusion Materials
- 2010 ASTM D3307-10 Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials
- 2008 ASTM D3307-08 Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials
- 2006 ASTM D3307-06 Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials
- 2004 ASTM D3307-04 Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials
- 2001 ASTM D3307-01 Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials
- 2000 ASTM D3307-00 Standard Specification for Perfluoroalkoxy (PFA)-Fluorocarbon Resin Molding and Extrusion Materials
