ISO 12215-1:2000
Small craft - Hull construction and scantlings - Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate

Standard No.

ISO 12215-1:2000

Release Date

2000

Published By

International Organization for Standardization (ISO)

Latest

ISO 12215-1:2000

Scope

This part of ISO 12215 is applicable to thermosetting resins and glass-fibre reinforcement used in the construction of small craft with a length of the hull (LH) of up to 24 m, in accordance with ISO 8666. This part of ISO 12215 specifies the minimum requirements for material properties of glass reinforcement and resin matrix and the reference laminate made thereof. This part of ISO 12215 may be applicable to materials other than those specified, provided that the minimum require-ments and properties of the reference laminate are met. NOTE The underlying reason for preparing this International Standard is to harmonize existing standards and recommended practices for loads on the hull and the dimensioning of small craft because they differ too considerably and thus limit general worldwide acceptability of boats.

ISO 12215-1:2000 Referenced Document

• DIN 16945:1989 Testing of resins, hardeners and accelerators, and catalyzed resins
• EN 59:1977 Glass Reinforced Plastics: Measurement of Hardness by Means of a Barcol Impressor
• ISO 14130:1997 Fibre-reinforced plastic composites - Determination of apparent interlaminar shear strength by short-beam method
• ISO 1675:1985 Plastics; Liquid resins; Determination of density by the pyknometer method
• ISO 178:1993 Plastics; determination of flexural properties
• ISO 1887:1995 Textile glass - Determination of combustible-matter content
• ISO 1889:1997 Reinforcement yarns - Determination of linear density
• ISO 2078:1993 Textile glass; yarns; designation
• ISO 2535:1997 Plastics - Unsaturated polyester resins - Measurement of gel time at 25 °C
• ISO 2555:1989 Plastics; resins in the liquid state or as emulsions or dispersions; determination of apparent viscosity by the Brookfield method
• ISO 2811-1:1997 Paints and varnishes - Determination of density - Part 1: Pyknometer method
• ISO 2884-1:1999 Paints and varnishes - Determination of viscosity using rotary viscometers - Part 1: Cone-and-plate viscometer operated at a high rate of shear
• ISO 3344:1997 Reinforcement products - Determination of moisture content
• ISO 3374:2000 Reinforcement products - Mats and fabrics - Determination of mass per unit area
• ISO 3521:1997 Plastics - Unsaturated polyester and epoxy resins - Determination of overall volume shrinkage
• ISO 4901:1985 Reinforced plastics based on unsaturated polyester resins; Determination of residual styrene monomer content
• ISO 527-1 Plastics — Determination of tensile properties — Part 1: General principles*， 2019-07-26 Update
• ISO 527-4 Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites*， 2023-03-24 Update
• ISO 62:1999 Plastics - Determination of water absorption
• ISO 75-1:1993 Plastics; determination of temperature of deflection under load; part 1: general test method
• ISO 75-2:1993 Plastics; determination of temperature of deflection under load; part 2: plastics and ebonite
• ISO 8666 Small craft — Principal data*， 2020-11-02 Update

ISO 12215-1:2000 history

• 2000 ISO 12215-1:2000 Small craft - Hull construction and scantlings - Part 1: Materials: Thermosetting resins, glass-fibre reinforcement, reference laminate