1.1 This classification system covers polychlorotrifluoroethylene (PCTFE) plastics that consist of at least 90 % chlorotrifluoroethylene and are suitable for extrusion and for compression and injection molding. Additional components allow for chemical modifications, such as co-monomers, but not colorants, fillers, plasticizers, or mechanical blends with other resins. This classification system does not cover recycled PCTFE materials.
1.2 The physical and electrical properties of parts molded or extruded from PCTFE molding compounds vary with the crystalline content obtained during processing and subsequent annealing. Accordingly, the numerical values listed in Table 1 apply only to the test specimens molded in accordance with Section 8. These values are not applicable as design criteria to semi-finished and finished parts prepared and annealed under other conditions.
1.3 The values stated in SI units as detailed in IEEE/SI-10 are to be regarded as the standard. The values given in parentheses are for information only.
1.4 The following precautionary statement pertains only to the test methods portion, Section 10, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—Although this classification system and ISO 20568-1 and ISO 20568-2 differ in approach or detail, data obtained using either are technically equivalent.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D1430-22 Referenced Document
ASTM D150 Standard Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation
ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
ASTM D3418 Standard Test Method for Transition Temperatures of Polymers By Differential Scanning Calorimetry
ASTM D3892 Standard Practice for Packaging/Packing of Plastics
ASTM D4591 Standard Test Method for Determining Temperatures and Heats of Transitions of Fluoropolymers by Differential Scanning Calorimetry
ASTM D4895 Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion
ASTM D618 Standard Practice for Conditioning Plastics for Testing
ASTM D621 Standard test method for particulate impurities in middle distillate fuels by laboratory filtration
ASTM D7194 Standard Specification for Aerospace Parts Machined from Polychlorotrifluoroethylene (PCTFE)
ASTM D7211 Standard Specification for Parts Machined from Polychlorotrifluoroethylene (PCTFE) and Intended for General Use*, 2023-05-17 Update
ASTM D792 Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
ASTM D883 Standard Terminology Relating to Plastics*, 2024-02-01 Update
IEEE SI 10 American National Standard for Metric Practice
ISO 20568-1 Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 1: Designation system and basis for specifications
ISO 20568-2 Plastics - Fluoropolymer dispersions and moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
ASTM D1430-22 history
2022ASTM D1430-22 Standard Classification System for Polychlorotrifluoroethylene (PCTFE) Plastics
2017ASTM D1430-17 Standard Classification System for Polychlorotrifluoroethylene (PCTFE) Plastics
2016ASTM D1430-11(2016) Standard Classification System for Polychlorotrifluoroethylene (PCTFE) Plastics
2011ASTM D1430-11 Standard Classification System for Polychlorotrifluoroethylene (PCTFE) Plastics
2010ASTM D1430-10 Standard Classification System for Polychlorotrifluoroethylene (PCTFE) Plastics
2003ASTM D1430-03(2008) Standard Classification System for Polychlorotrifluoroethylene (PCTFE) Plastics
2003ASTM D1430-03 Standard Classification System for Polychlorotrifluoroethylene (PCTFE) Plastics
2000ASTM D1430-00 Standard Classification System for Polychlorotrifluoroethylene (PCTFE) Plastics