ASTM D6358-19e1
Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) Injection Molding, Extrusion and Blow Molding Materials Using ISO Methods

Standard No.

ASTM D6358-19e1

Release Date

2019

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM D6358-19e1

Scope

1.1 This classification system covers unfilled, reinforced filled, and impact modified materials suitable for injection molding, extrusion and blow molding using ISO methods. The system allows for the use of poly (phenylene sulfide) (PPS) plastic materials that are recycled, reconstituted recycledregrind, recovered or reprocessed, or both, provided that the requirements as stated in this specification are met. It is the responsibility of the supplier and the buyer of recycled, reconstituted, recycled-regrind, recovered or reprocessed, or both, poly (phenylene sulfide) plastic materials to ensure compliance (see Guide D7209). 1.2 The properties included in this classification are those required to identify the compositions covered. It is possible that other requirements are necessary to identify particular characteristics important to specialized applications. The use of suffixes as shown in Section 5 is one way of specifying these requirements. 1.3 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection needs to be made by those having expertise in the plastic field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification. 1.4 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—This standard and ISO 28078 address the same subject matter, but differ in technical content. NOTE 2—ASTM D4067 for PPS uses ASTM test methods. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D6358-19e1 Referenced Document

• ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
• ASTM D3641 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
• ASTM D3892 Standard Practice for Packaging/Packing of Plastics
• ASTM D4000 Standard Classification System for Specifying Plastic Materials*， 2023-03-15 Update
• ASTM D4067 Standard Specification for Reinforced and Filled Polyphenylene Sulfide (PPS) Injection Molding and Extrusion Materials
• ASTM D618 Standard Practice for Conditioning Plastics for Testing*， 2021-07-15 Update
• ASTM D7209 Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products *， 2024-04-22 Update
• ASTM D883 Standard Terminology Relating to Plastics*， 2024-02-01 Update
• ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
• ISO 1133 Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics; Technical Corrigendum 1
• ISO 11443 Plastics - Determination of the fluidity of plastics using capillary and slit-die rheometers*， 2021-01-31 Update
• ISO 1183 Plastics; Methods for determining the density and relative density of non-cellular plastics
• ISO 178 Surface chemical analysis — Secondary ion mass spectrometry — Linearity of intensity scale in single ion counting time-of-flight mass analysers
• ISO 180 Plastics. Determination of Izod impact strength*， 2023-06-07 Update
• ISO 28078 Plastics - Poly(phenylene sulfide) (PPS) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
• ISO 294-1 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens
• ISO 3167 Plastics - Multipurpose test specimens
• ISO 3451 Withdrawal of ISO 3451-1976
• ISO 527 Plastics — Determination of tensile properties — Part 5: Test conditions for unidirectional fibre-reinforced plastic composites*， 2021-11-24 Update
• ISO 604 Plastics - Determination of compressive properties
• ISO 62 Plastics - Determination of water absorption

ASTM D6358-19e1 history

• 2019 ASTM D6358-19e1 Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) Injection Molding, Extrusion and Blow Molding Materials Using ISO Methods
• 2019 ASTM D6358-19 Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) Injection Molding, Extrusion and Blow Molding Materials Using ISO Methods
• 2011 ASTM D6358-11 Standard Classification System and Basis for Specification for Poly (Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ISO Methods
• 2006 ASTM D6358-06 Standard Classification System for Poly (Phenylene Sulfide) Injection Molding and Extrusion Materials Using ISO Methods
• 1999 ASTM D6358-99 Standard Classification System for Poly (Phenylene Sulfide) Injection Molding and Extrusion Materials Using ISO Methods