ASTM D5336-15a
Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Material

Standard No.

ASTM D5336-15a

Release Date

2015

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM D5336-21

Latest

ASTM D5336-22

Scope

1.1 This classification system covers polyphthalamide materials suitable for injection molding. 1.2 The properties included in this classification system are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using suffixes as given in Section 5. 1.3 This classification system allows for the use of recycled materials provided that all specification requirements are met. 1.4 This classification system is intended to be a means of calling out plastics materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastics field only after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this classification system. 1.5 The values stated in SI units are to be regarded as the standard (see IEEE/ASTM SI-10). The values given in parentheses are for information only. 1.6 The following precautionary caveat pertains only to the test methods portion, Section 11, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 11.7.1. NOTE 1—There is no known ISO equivalent to this standard.

ASTM D5336-15a Referenced Document

• ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
• ASTM D256 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics*， 2023-03-15 Update
• ASTM D2857 Standard Practice for Dilute Solution Viscosity of Polymers
• ASTM D3418 Standard Test Method for Transition Temperatures of Polymers By Differential Scanning Calorimetry
• ASTM D3641 Standard Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials
• ASTM D3801 Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position
• ASTM D3835 Standard Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer
• ASTM D3892 Standard Practice for Packaging/Packing of Plastics
• ASTM D4000 Standard Classification System for Specifying Plastic Materials*， 2023-03-15 Update
• ASTM D5225 Standard Test Method for Measuring Solution Viscosity of Polymers with a Differential Viscometer
• ASTM D5630 Standard Test Method for Ash Content in Thermoplastics
• ASTM D618 Standard Practice for Conditioning Plastics for Testing*， 2021-07-15 Update
• ASTM D638 Standard Test Method for Tensile Properties of Plastics
• ASTM D648 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position*， 2024-04-21 Update
• ASTM D6869 Standard Test Method for Coulometric and Volumetric Determination of Moisture in Plastics Using the Karl Fischer Reaction (the Reaction of Iodine with Water)*， 2017-12-01 Update
• ASTM D7209 Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products *， 2024-04-21 Update
• ASTM D790 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials*， 2024-04-21 Update
• ASTM D792 Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
• ASTM D883 Standard Terminology Relating to Plastics*， 2024-02-01 Update
• ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
• IEEE/ASTM SI 10 American National Standard for Metric Practice
• ISO 15512 Plastics — Determination of water content*， 2019-04-30 Update
• ISO 179-1 Plastics. Determination of Charpy impact properties - Non-instrumented impact test*， 2023-06-07 Update
• ISO 294-1 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens*， 2017-05-01 Update
• ISO 3451-1 Plastics — Determination of ash — Part 1: General methods*， 2019-02-06 Update
• ISO 3451-4 Plastics — Determination of ash — Part 4: Polyamides*， 2024-01-01 Update
• ISO 527-1 Plastics — Determination of tensile properties — Part 1: General principles*， 2019-07-26 Update
• ISO 527-2 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics
• ISO 75-1 Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics*， 2020-02-28 Update
• ISO 75-2 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite

ASTM D5336-15a history

• 2022 ASTM D5336-22 Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Materials
• 2021 ASTM D5336-21 Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Materials
• 2015 ASTM D5336-15a Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Material
• 2015 ASTM D5336-15 Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Materials
• 2009 ASTM D5336-09 Standard Specification for Polyphthalamide (PPA) Injection Molding Materials
• 2003 ASTM D5336-03 Standard Specification for Polyphthalamide (PPA) Injection Molding Materials
• 2000 ASTM D5336-00 Standard Specification for Polyphthalamide (PPA) Injection Molding Materials