ASTM B150/B150M-12(2017)
Standard Specification for Aluminum Bronze Rod, Bar, and Shapes
- Standard No.
- ASTM B150/B150M-12(2017)
- Release Date
- 2012
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM B150/B150M-19
- Latest
- ASTM B150/B150M-19
- Scope
1.1 This specification establishes the requirements for aluminum bronze rod, bar, and shapes for Copper Alloys UNS Nos. C61300, C61400, C61900, C62300, C62400, C63000, C63020, C63200, C64200, and C64210.
Note 1: Product intended for hot forging is described in Specification B124/B124M.
Note 2: Warning—Mercury has been designated by many regulatory agencies as a hazardous material that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM B150/B150M-12(2017) Referenced Document
- ASTM B124/B124M Standard Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
- ASTM B154 Standard Test Method for Mercurous Nitrate Test for Copper and Copper Alloys
- ASTM B249/B249M Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
- ASTM B601 Standard Classification for Temper Designations for Copper and Copper Alloys-Wrought and Cast
- ASTM B858 Standard Test Method for Ammonia Vapor Test for Determination Susceptibility to Stress Corrosion Cracking in Copper Alloys
- ASTM E118 Standard Test Methods for Chemical Analysis of Copper-Chromium Alloys
- ASTM E18 Standard Test Methods for Rockwell Hardness of Metallic Materials
- ASTM E478 Standard Test Methods for Chemical Analysis of Copper Alloys
- ASTM E53 Standard Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
- ASTM E62 Standard Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
- ASTM E8/E8M Standard Test Methods for Tension Testing of Metallic Materials
ASTM B150/B150M-12(2017) history
- 2019 ASTM B150/B150M-19 Standard Specification for Aluminum Bronze Rod, Bar, and Shapes
- 2012 ASTM B150/B150M-12(2017) Standard Specification for Aluminum Bronze Rod, Bar, and Shapes
- 2012 ASTM B150/B150M-12 Standard Specification for Aluminum Bronze Rod, Bar, and Shapes
- 2008 ASTM B150/B150M-08 Standard Specification for Aluminum Bronze Rod, Bar, and Shapes
- 2003 ASTM B150/B150M-03 Standard Specification for Aluminum Bronze Rod, Bar, and Shapes
- 2002 ASTM B150/B150M-02 Standard Specification for Aluminum Bronze Rod, Bar, and Shapes
- 2017 ASTM B150-98e2 Standard Specification for Aluminum Bronze Rod, Bar, and Shapes (Withdrawn 2002)
