ASTM D1074-17
Standard Test Method for Compressive Strength of Asphalt Mixtures

Standard No.

ASTM D1074-17

Release Date

2017

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM D1074-17

Scope

3.1 The compressive strength of specimens prepared and tested by this test method along with density and voids properties are used for laboratory mix design of asphalt mixtures. One approach is described in ASTM STP 252.4

3.1.1 This test method also describes the methods for molding, curing, and testing of specimens being evaluated by Test Method D1075.

3.1.2 When used in conjunction with other mixture physical properties, the compressive strength may contribute to the overall mixture characterization and is one factor determining its suitability for use under given loading conditions and environment as a highway paving material.

3.2 Typical values of minimum compressive strengths for design of asphalt mixtures by this test method for different traffic densities are given in Table 401-1 of the Standard Specifications for Construction of Roads and Bridges on Federal Highway Projects.3 Some state departments of transportation and federal agencies have specific requirements of their own based on their experience with this test method. The agencies should be consulted for their specific requirements if work is to meet their standards.

3.3 Reheated mixtures are permissible in this test method, but the resulting compressive strengths will be higher than for newly prepared mixtures due to the change in the binder viscosity, an element of the compressive strength as measured under these loading conditions and temperature.5

Note 1: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing/sampling/inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.

1.1 This test method provides a method for measuring the compressive strength of compacted asphalt mixtures. It is for use with specimens weighed, batched, mixed, and fabricated in the laboratory, as well as for mixtures manufactured in a hot-mix plant.

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 The text of this standard references notes a......

ASTM D1074-17 Referenced Document

• ASTM C136 Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
• ASTM C670 Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials
• ASTM C702 Standard Practice for Reducing Samples of Aggregate to Testing Size
• ASTM D1075 Standard Test Method for Effect of Water on Compressive Strength of Compacted Bituminous Mixtures
• ASTM D140 Standard Practice for Sampling Bituminous Materials
• ASTM D2041 Standard Test Method for Theoretical Maximum Specific Gravity and Density of Bituminous Paving Mixtures
• ASTM D2726 Standard Test Method for Bulk Specific Gravity and Density of Non-Absorptive Compacted Bituminous Mixtures
• ASTM D3203 Standard Test Method for Percent Air Voids in Compacted Dense and Open Bituminous Paving Mixtures
• ASTM D3666 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials
• ASTM D4753 Standard Specification for Evaluating, Selecting, and Specifying Balances and Scales for Use in Soil, Rock, and Construction Materials Testing
• ASTM D75 Standard Practice for Sampling Aggregates
• ASTM D979 Standard Practice for Sampling Bituminous Paving Mixtures
• ASTM E2251 Standard Specification for Liquid-in-Glass ASTM Thermometers with Low-Hazard Precision Liquids
• ASTM E4 Standard Practices for Force Verification of Testing Machines

ASTM D1074-17 history

• 2017 ASTM D1074-17 Standard Test Method for Compressive Strength of Asphalt Mixtures
• 2009 ASTM D1074-09 Standard Test Method for Compressive Strength of Bituminous Mixtures
• 2002 ASTM D1074-02 Standard Test Method for Compressive Strength of Bituminous Mixtures
• 1996 ASTM D1074-96 Standard Test Method for Compressive Strength of Bituminous Mixtures