ISO 21304-2:2021 Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
International Organization for Standardization (ISO)
Latest
ISO 21304-2:2021
Scope
This document specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of PE-UHMW moulding and extrusion materials. It gives the requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing.
This document gives the procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made. Properties and test methods which are suitable and necessary to characterize PE-UHMW moulding and extrusion materials are listed.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in wide use for or of particular significance to these moulding and extrusion materials are also included in this document, as are the designatory properties specified in ISO 21304-1. This document specifies the materials with MFR less than 0,1 g/10 min at 190 °C /21,6 kg based on ISO 17855-1.
The methods of preparation and conditioning, the specimen dimensions and the test procedures specified in this document are used in order to obtain reproducible and comparable test results. Values determined will not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.
ISO 21304-2:2021 Referenced Document
IEC 60112 Method for the determination of the proof and the comparative tracking indices of solid insulating materials
IEC 60243-1 Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies
IEC 60296 Fluids for electrotechnical applications – Mineral insulating oils for electrical equipment
IEC 62631-2-1 Dielectric and resistive properties of solid insulating materials - Part 2-1: Relative permittivity and dissipation factor - Technical frequencies (0,1 Hz to 10 MHz) - AC methods
IEC 62631-3-1 Dielectric and resistive properties of solid insulating materials - Part 3-1: Determination of resistive properties (DC methods) - Volume resistance and volume resistivity - General method*, 2023-01-23 Update
IEC 62631-3-2 Dielectric and resistive properties of solid insulating materials — Part 3-2: Determination of resistive properties (DC methods) — Surface resistance and surface resistivity*, 2023-10-16 Update
ISO 10350-1 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials
ISO 1133-1 Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics — Part 1: Standard method*, 2022-06-23 Update
ISO 11357-2 Plastics — Differential scanning calorimetry (DSC) — Part 2: Determination of glass transition temperature and step height
ISO 11357-3 Plastics - Differential scanning calorimetry (DSC) - Part 3: Determination of temperature and enthalpy of melting and crystallization
ISO 11359-2 Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature*, 2021-11-12 Update
ISO 1183-1 Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pycnometer method and titration method
ISO 1183-2 Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method
ISO 15527 Plastics — Compression-moulded sheets of polyethylene (PE-UHMW, PE-HD) — Requirements and test methods*, 2022-02-10 Update
ISO 1628-3 Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 3: Polyethylenes and polypropylenes
ISO 178 Surface chemical analysis — Secondary ion mass spectrometry — Linearity of intensity scale in single ion counting time-of-flight mass analysers
ISO 179-1 Plastics. Determination of Charpy impact properties - Non-instrumented impact test*, 2023-06-07 Update
ISO 21304-1 Plastics — Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials — Part 1: Designation system and basis for specifications
ISO 2818 Plastics — Preparation of test specimens by machining
ISO 291 Plastics - Standard atmospheres for conditioning and testing
ISO 293 Plastics — Compression moulding of test specimens of thermoplastic materials*, 2023-02-21 Update
ISO 4589-2 Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test
ISO 527-1 Plastics — Determination of tensile properties — Part 1: General principles
ISO 527-2 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics
ISO 527-4 Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites*, 2023-03-24 Update
ISO 62 Plastics - Determination of water absorption
ISO 75-1 Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
ISO 75-2 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite
ISO 899-1 Plastics - Determination of creep behaviour - Part 1: Tensile creep
ISO 21304-2:2021 history
2021ISO 21304-2:2021 Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties