EN ISO 15156-3:2015 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys (ISO 15156-3:2015)
This part of ISO 15156 specifies requirements and provides recommendations for the selection and qualification of high alloy steels (CRAs) (corrosion-resistant alloys) and other alloys for use in oil and gas production facilities and natural gas treatment facilities in H2S-containing environments, their failure may pose a possible health and safety risk to the general public and personnel or to the environment. It can be used to avoid costly damage due to corrosion of the system itself. It supplements, but does not replace, the requirements for materials contained in relevant design guidelines, standards or regulations. This part of ISO 15156 addresses the resistance of these materials to damage that can be caused by H2S-induced stress corrosion cracking (SSC), stress corrosion cracking (SCC) and galvanically induced hydrogen cracking (GHSC). This part of ISO 15156 deals only with cracking. It does not address material losses due to general (mass loss-related) or localized corrosion. Table 1 provides a non-exhaustive list of equipment falling within the scope of this part of ISO 15156, including approved exceptions. This part of ISO 15156 applies to the qualification and selection of materials for equipment designed and constructed using load-driven design methods. For designs that use strain-based design methods, see ISO 15156-1:2015, Section 5. This part of ISO 15156 is not necessarily suitable for application to equipment in refining or downstream processes and facilities.
EN ISO 15156-3:2015 Referenced Document
ASTM A182/A182M-15 Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service*， 2024-04-20 Update
ASTM A213/A213M-15 Standard Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes*， 2024-04-20 Update
ASTM A276-13 Standard Specification for Stainless Steel Bars and Shapes*， 2024-04-20 Update
ASTM A351/A351M-14 Standard Specification for Castings, Austenitic, for Pressure-Containing Parts*， 2024-04-20 Update
ASTM A743/A743M-13 Standard Specification for Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion Resistant, for General Application*， 2024-04-20 Update
ASTM A744/A744M-13 Standard Specification for Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe Service*， 2024-04-20 Update
ASTM A747/A747M-12 Standard Specification for Steel Castings, Stainless, Precipitation Hardening*， 2024-04-20 Update
ASTM E18-15 Standard Test Methods for Rockwell Hardness of Metallic Materials
ASTM E29-13 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications*， 2024-04-20 Update
ASTM E384-11 Standard Test Method for Knoop and Vickers Hardness of Materials*， 2024-04-20 Update
ASTM E562-11 Standard Test Method for Determining Volume Fraction by Systematic Manual Point Count*， 2024-04-20 Update
EN ISO 15156-3:2015 history
2020EN ISO 15156-3:2020 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys (ISO 15156-3:2020)
2015EN ISO 15156-3:2015 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys (ISO 15156-3:2015)
2009EN ISO 15156-3:2009 Petroleum and natural gas industries - Materials for use in H2S-containing environments in oil and gas production - Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys
2003EN ISO 15156-3:2003 Petroleum, petrochemical and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys Incorporating Corrigendum March 2006; ISO 15156