ISO 13766-1:2018
Earth-moving and building construction machinery - Electromagnetic compatibility (EMC) of machines with internal electrical power supply - Part 1: General EMC requirements under typical electromagnetic environmental conditions

Standard No.

ISO 13766-1:2018

Release Date

2018

Published By

International Organization for Standardization (ISO)

Latest

ISO 13766-1:2018

Scope

This document provides test methods and acceptance criteria for the evaluation of the electromagnetic compatibility (EMC) of earth-moving machinery, as defined in ISO 6165:2012, and of the following building construction machinery as defined in ISO/TR 12603:2010: — drilling and foundation equipment; — equipment used for the preparation, conveyance and compaction of concrete, mortar and processing reinforcement; — road construction and maintenance machinery and equipment. It deals with general EMC requirements under typical electromagnetic environmental conditions. Electrical/electronic subassemblies (ESA) and separate ESA intended to be fitted to the machinery are also dealt with. The following electromagnetic disturbance phenomena are evaluated: — broadband and narrowband electromagnetic interference; — electromagnetic field immunity; — electrostatic discharge; — conducted transients. The machinery can have DC or AC or a combination of both as the internal electrical power supply system. This document is not applicable to machines that are designed to be supplied by an external mains network or to phenomena caused by military applications. NOTE 1 NOTE 2 Grid-connected machines are covered by IEC 61000. Hybrid machines are covered in UN ECE R10-Rev. 5.

ISO 13766-1:2018 Referenced Document

• CISPR 12 AMD 1-2009 Vehicles, boats and internal combustion engines – Radio disturbance characteristics – Limits and methods of measurement for the protection of offboard receivers AMENDMENT 1
• CISPR 12-2007 Vehicles, boats, and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of off-board receivers
• CISPR 16-1-4 Edition 3.1-2012 Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-4: Radio disturbance and immunity measuring apparatus - Antennas and test sites for radiated disturbance measurements
• CISPR 16-2-3-2016 Spécifications des méthodes et des appareils de mesure des perturbations radioélectriques et de l’immunité aux perturbations radioélectriques – Partie 2-3: Méthodes de mesure des perturbations et de l'immunité – Mesurages des perturbations rayonnées (Edit
• CISPR 25-2008 Vehicles, boates and internal combustion engines - Radio disturbance characteristics - Limits and methods of measurement for the protection of on-board receivers
• IEC 60050-161:1990 International elektrotechnical vocabulary; chapter 161: electromagnetic compatibility
• ISO 10605:2008 Road vehicles - Test methods for electrical disturbances from electrostatic discharge
• ISO 11451-1:2015 Road vehicles - Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 1: General principles and terminology
• ISO 11451-2:2015 Road vehicles - Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 2: Off-vehicle radiation sources
• ISO 11451-3:2015 Road vehicles - Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 3: On-board transmitter simulation
• ISO 11451-4:2013 Road vehicles - Vehicle test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 4: Bulk current injection (BCI)
• ISO 11452-1:2015 Road vehicles — Component test methods for electrical disturbances from narrowband radiated electromagnetic energy — Part 1: General principles and terminology
• ISO 11452-2:2004 Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 2: Absorber-lined shielded enclosure
• ISO 11452-3:2016 Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 3: Transverse electromagnetic (TEM) cell
• ISO 11452-4:2011 Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 4: Harness excitation methods
• ISO 11452-5:2002 Road vehicles - Component test methods for electrical disturbances by narrowband radiated electromagnetic energy - Part 5: Stripline
• ISO 12100:2010 Safety of machinery - General principles for design - Risk assessment and risk reduction
• ISO 13766-2:2018 Earth-moving and building construction machinery — Electromagnetic compatibility (EMC) of machines with internal electrical power supply — Part 2: Additional EMC requirements for functional safety*， 2018-04-09 Update
• ISO 16750-1:2006 Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 1: General
• ISO 16750-2:2012 Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 2: Electrical loads
• ISO 21848:2005 Road vehicles - Electrical and electronic equipment for a supply voltage of 42 V - Electrical loads
• ISO 6165:2012 Earth-moving machinery - Basic types - Identification and terms and definitions
• ISO 7637-1:2015 Road vehicles - Electrical disturbances from conduction and coupling - Part 1: Definitions and general considerations
• ISO 7637-2:2011 Road vehicles - Electrical disturbances from conduction and coupling - Part 2: Electrical transient conduction along supply lines only
• ISO/TR 12603:2010 Building construction machinery and equipment - Classification

ISO 13766-1:2018 history

• 2018 ISO 13766-1:2018 Earth-moving and building construction machinery - Electromagnetic compatibility (EMC) of machines with internal electrical power supply - Part 1: General EMC requirements under typical electromagnetic environmental conditions