ISO 16228:2017
Fasteners - Types of inspection documents

Standard No.

ISO 16228:2017

Release Date

2017

Published By

International Organization for Standardization (ISO)

Latest

ISO 16228:2017

Scope

This document specifies the different types of fastener inspection documents issued by the fastener manufacturer or distributor and/or by the external authorized representative on specific request of the purchaser at the time of the order. — declaration of compliance (F2.1); — test reports (F2.2, F3.1 and F3.2). NOTE The term “certificate” is in common use, however for fastener inspection documents the terminology to be used is “test report”. This document specifies requirements for the content of each fastener inspection document, in conjunction with the order, the relevant standards and/or specified requirements. This document is applicable to finished fasteners such as bolts, screws, studs, nuts, washers, pins, rivets, etc. made of steel, stainless steel, non-ferrous metal or non-metallic material. This document does not apply to special-purpose or specially engineered applications requiring other types of procedures (e.g. initial samples). Examples of inspection documents are given in Annex A. An example of a coding system identifying the sections in fastener inspection documents is given in Annex B.

ISO 16228:2017 Referenced Document

• EN 10168:2004 Steel products - Inspection documents - List of information and description
• EN 10204:2004 Metallic products - Types of inspection documents*， 2024-04-20 Update
• ISO 10474:2013 Steel and steel products - Inspection documents
• ISO 10666:1999 Drilling screws with tapping screw thread - Mechanical and functional properties
• ISO 10683:2014 Fasteners - Non-electrolytically applied zinc flake coatings
• ISO 10684:2004 Fasteners - Hot dip galvanized coatings
• ISO 14589:2000 Blind rivets - Mechanical testing
• ISO 15330:1999 Fasteners - Preloading test for the detection of hydrogen embrittlement - Parallel bearing surface method
• ISO 15977:2002 Open end blind rivets with break pull mandrel and protruding head - AIA/St
• ISO 160 Asbestos-cement pressure pipes and joints
• ISO 225:2010 Fasteners - Bolts, screws, studs and nuts - Symbols and descriptions of dimensions
• ISO 2320:2015 Fasteners - Prevailing torque steel nuts - Functional properties
• ISO 2702:2011 Heat-treated steel tapping screws - Mechanical properties
• ISO 3269:2000 Fasteners - Acceptance inspection
• ISO 3506-1:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs
• ISO 3506-2:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts
• ISO 3506-3:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress
• ISO 3506-4:2009 Mechanical properties of corrosion-resistant stainless steel fasteners - Part 4: Tapping screws
• ISO 3800:1993 Threaded fasteners; axial load fatigue testing; test methods and evaluation of results
• ISO 4014:2011 Hexagon head bolts - Product grades A and B
• ISO 4032:2012 Hexagon regular nuts (style 1) - Product grades A and B
• ISO 4042:1999 Fasteners - Electroplated coatings
• ISO 4759-1:2000 Tolerances for fasteners - Part 1: Bolts, screws, studs and nuts - Product grades A, B and C
• ISO 6157-1:1988 Fasteners surface discontinuities; part 1: bolts, screws and studs for general requirements
• ISO 6157-2:1995 Fasteners - Surface discontinuities - Part 2: Nuts
• ISO 6157-3:1988 Fasteners; surface discontinuities; part 3: bolts, screws and studs for special requirements
• ISO 7089:2000 Plain washers - Normal series - Product grade A
• ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread
• ISO 898-2:2012 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 2: Nuts with specified property classes - Coarse thread and fine pitch thread
• ISO 898-3 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 3: Flat washers with specified property classes — Amendment 1*， 2020-08-11 Update
• ISO 898-5:2012 Mechanical properties of fasteners made of carbon steel and alloy steel - Part 5: Set screws and similar threaded fasteners with specified hardness classes - Coarse thread and fine pitch thread
• ISO 9001:2015 Quality management systems - Requirements
• ISO/TR 6306:1989 Chemical analysis of steel; order of listing elements

ISO 16228:2017 history

• 2017 ISO 16228:2017 Fasteners - Types of inspection documents