ASTM D6775-13(2017)
Standard Test Method for Breaking Strength and Elongation of Textile Webbing, Tape and Braided Material
- Standard No.
- ASTM D6775-13(2017)
- Release Date
- 2013
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D6775-13(2024)
- Latest
- ASTM D6775-13(2024)
- Scope
-
5.1 This test method can be used for acceptance testing of commercial shipments but comparisons should be made with caution because estimates of between-laboratory precision are incomplete.
5.1.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, use samples for such comparative tests that are as homogeneous as possible, drawn from the same lot of material as the samples that resulted in disparate results during initial testing, and randomly assigned in equal numbers to each laboratory. The test results from the laboratories involved should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.
5.2 Elongation is an indication of the ability of a fiber to absorb energy. The elongation of textile materials must be great enough to withstand strains experienced in processing and end use, and to absorb the energies of applied forces repeatedly.
1.1 This test method covers the determination of the breaking strength and elongation of textile webbing, tape and braided materials using a split-drum type specimen clamp.
1.2 This test method is limited to materials with a maximum width of 90 mm (3.5 in.) and a maximum breaking strength of no more than 89000 N (20000 lb).
1.3 The values stated in either SI units or U.S. Customary units are to be regarded separately as standard. Within the text, the U.S. Customary units are given in parentheses. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D6775-13(2017) Referenced Document
- ASTM D123 Standard Terminology Relating to Textiles
- ASTM D1776 Standard Practice for Conditioning and Testing Textiles
- ASTM D4848 Standard Terminology Related to Force, Deformation and Related Properties of Textiles
- ASTM D4850 Standard Terminology Relating to Fabrics and Fabric Test Methods
- ASTM D76 Standard Specification for Tensile Testing Machines for Textiles
ASTM D6775-13(2017) history
- 2024 ASTM D6775-13(2024) Standard Test Method for Breaking Strength and Elongation of Textile Webbing, Tape and Braided Material
- 2013 ASTM D6775-13(2017) Standard Test Method for Breaking Strength and Elongation of Textile Webbing, Tape and Braided Material
- 2013 ASTM D6775-13 Standard Test Method for Breaking Strength and Elongation of Textile Webbing, Tape and Braided Material
- 2011 ASTM D6775-02(2011) Standard Test Method for Breaking Strength and Elongation of Textile Webbing, Tape and Braided Material
- 2002 ASTM D6775-02(2007) Standard Test Method for Breaking Strength and Elongation of Textile Webbing, Tape and Braided Material
- 2002 ASTM D6775-02e1 Standard Test Method for Breaking Strength and Elongation of Textile Webbing, Tape and Braided Material
- 2002 ASTM D6775-02 Standard Test Method for Breaking Strength and Elongation of Textile Webbing, Tape and Braided Material
