IEC 62282-3-400:2016
Fuel cell technologies - Part 3-400: Stationary fuel cell power systems - Small stationary fuel cell power system with combined heat and power output

Standard No.

IEC 62282-3-400:2016

Release Date

2016

Published By

International Electrotechnical Commission (IEC)

Latest

IEC 62282-3-400:2016

Replace

IEC 105/620/FDIS:2016

Scope

This part of IEC 62282 applies to small stationary fuel cell power systems serving as a heating appliance providing both electric power and useful heat with or without a supplementary heat generator providing peak load function. This standard applies to fuel cell power systems that are intended to be permanently connected to the electrical system of the customer (end user). Direct connection to the mains (parallel operation) is also within the scope of this standard. NOTE 1 Parallel operation is subject to the permission of the local electric power supply utility. This standard is limited to gas and liquid fuelled fuel cell CHP appliances that have a heat input based on lower heating value of less than or equal to 70 kW. For some regional applications@ the output electric power is limited. Specific limitations are given in Clause C.1 for Japan. This standard applies to systems as shown in Figure 1. One is a system where both stationary fuel cell power system and supplementary heat generator are installed in one enclosure without any partition. This standard does not have to apply to the supplementary heat generator of systems where the stationary fuel cell power system and the supplementary heat generator are not built in one enclosure@ and whose ducts are not common (that is@ each appliance has its own dedicated duct system). This standard applies to systems intended for operation on the following supplied input fuels: ?C natural gas and other methane rich gases; ?C fuels derived from oil refining (liquefied petroleum gases@ propane@ and butane); ?C hydrogen as supply gas for the CHP generator. NOTE 2 It is possible that other fuels such as alcohols (methanol@ ethanol)@ kerosene@ or hydrogen for the supplementary heat generatorwill be added in future amendments or revisions. This part of IEC 62282 applies to systems where: ?C the heat transfer fluid (heat output) is water or a mixture of water and additives to prevent corrosion and to prevent freezing; ?C the heat transfer fluid circuit (heat output) can be designed for open or sealed operation; ?C the maximum temperature of the heat transfer fluid (heat output) does not exceed 100 ?? or the value given in Clause B.1 for Europe or in Clause D.1 for the USA; ?C the maximum pressure of the heat transfer fluid (heat output) circuit does not exceed 0@3 MPa@ or the limits given in Clause B.1 for Europe@ or C.4.3 for Japan or Clause D.1 for the USA; ?C the maximum pressure of the domestic hot water circuit@ if installed@ does not exceed 0@1 MPa@ or the limits as given in Clause D.1 for the USA. This standard applies to systems with either condensing or non-condensing conditions in the exhaust gas. This standard applies to appliances ?C with ducts included as part of the appliance (Type B@ Type C) and ?C without ducts (Type A) Duct systems are shown in Annex F. The chimney in the figures is part of the building and is not within the scope of this standard. Different combustion air/flue duct circuit configurations are accommodated@ see Annex F. This standard applies to both indoor and outdoor installations. This standard applies to type testing only. This standard specifies the requirements for construction@ safety@ installation@ fitness for purpose@ rational use of energy@ marking@ and performance measurement of these appliances. This standard also provides regional and country specific requirements to facilitate the worldwide application of this IEC standard. These essential regional and country specific requirements are given in Annex B for Europe@ in Annex C for Japan and in Annex D for the USA. If the user or manufacturer chooses a regional specific annex to apply this standard@ then that annex applies to the appliance in its entirety without mixing requirements between annexes. The chosen regional or country specific annex becomes normative

IEC 62282-3-400:2016 Referenced Document

• CISPR 14-1-2016 Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission
• CISPR 14-2-2015 Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 2: Immunity - Product family standard
• IEC 60079-0:2011 Explosive atmospheres - Part 0: Equipment - General requirements
• IEC 60079-10-1:2015 Explosive atmospheres - Part 10-1: Classification of areas - Explosive gas atmospheres
• IEC 60079-10-2:2015 Explosive atmospheres - Part 10-2: Classification of areas - Explosive dust atmospheres
• IEC 60079-11:2011 Explosive atmospheres - Part 11: Equipment protection by intrinsic safety "i"
• IEC 60079-1:2014 Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
• IEC 60079-2:2014 Explosive atmospheres - Part 2: Equipment protection by pressurized enclosure "p"
• IEC 60079-5:2015 Explosive atmospheres - Part 5: Equipment protection by powder filling "q"
• IEC 60079-6:2015 Explosive atmospheres - Part 6: Equipment protection by liquid immersion "o"
• IEC 60079-7:2015 Explosive atmospheres - Part 7: Equipment protection by increased safety "e"

IEC 62282-3-400:2016 history

• 2016 IEC 62282-3-400:2016 Fuel cell technologies - Part 3-400: Stationary fuel cell power systems - Small stationary fuel cell power system with combined heat and power output