ASTM C1780-17
Standard Practice for Installation Methods for Adhered Manufactured Stone Masonry Veneer
- Standard No.
- ASTM C1780-17
- Release Date
- 2017
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM C1780-18
- Latest
- ASTM C1780-23a
- Scope
-
1.1 This practice is intended to provide accepted procedures to designers and installers of adhered manufactured stone masonry veneer in residential and commercial construction. This information is meant to complement the specific installation instructions provided by manufacturers of adhered manufactured stone masonry veneers and recognized building codes, but is not meant to replace them. This practice does not address installation methods or techniques for all materials in the building envelope. This practice covers the installation of adhered manufactured stone masonry veneer units for application as adhered veneer to exterior and interior walls, columns, landscape structures and other structures suitable to receive adhered veneer. The units included in this practice are manufactured to meet the requirements of Specification C1670. This practice is limited to the installation of units. This practice does not cover all flashing or moisture management requirements. Refer to the applicable building code and project documents for additional flashing and moisture management requirements.
Note 1: The Masonry Veneer Manufacturers Association (MVMA) publication Installation Guide for Adhered Concrete Masonry Veneer provides generally accepted methods and details for installation and flashing.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 All workmanship and materials related to the installation of adhered manufactured stone masonry veneer units shall meet the requirements of the contract documents and building code having jurisdiction over the project.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.2)
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM C1780-17 Referenced Document
- ASTM C1032 Standard Specification for Woven Wire Plaster Base
- ASTM C1059 Standard Specification for Latex Agents for Bonding Fresh To Hardened Concrete
- ASTM C1063 Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster
- ASTM C1180 Standard Terminology of Mortar and Grout for Unit Masonry
- ASTM C1232 Standard Terminology for Masonry
- ASTM C1325 Standard Specification for Non-Asbestos Fiber-Mat Reinforced Cement Interior Substrate Sheets
- ASTM C1384 Standard Specification for Admixtures for Masonry Mortars
- ASTM C1670 Standard Specification for Adhered Manufactured Stone Masonry Veneer (AMSMV) Units
- ASTM C1714/C1714M Standard Specification for Preblended Dry Mortar Mix for Unit Masonry
- ASTM C270 Standard Specification for Mortar For Unit Masonry
- ASTM C482 Standard Test Method for Bond Strength of Ceramic Tile to Portland Cement Paste
- ASTM C847 Standard Specification for Metal Lath
- ASTM C90 Standard Specification for Loadbearing Concrete Masonry Units
- ASTM C926 Standard Specification for Application of Portland Cement-Based Plaster
- ASTM C932 Standard Specification for Surface-Applied Bonding Agents for Exterior Plastering
- ASTM C933 Standard Specification for Welded Wire Lath
- ASTM C979 Standard Specification for Pigments for Integrally Colored Concrete
- ASTM E2556/E2556M Standard Specification for Vapor Permeable Flexible Sheet Water-Resistive Barriers Intended for Mechanical Attachment
ASTM C1780-17 history
- 2023 ASTM C1780-23a Standard Practice for Installation Methods for Cement-based Adhered Masonry Veneer
- 2023 ASTM C1780-23 Standard Practice for Installation Methods for Cement-based Adhered Masonry Veneer
- 2020 ASTM C1780-20 Standard Practice for Installation Methods for Cement-based Adhered Masonry Veneer
- 2018 ASTM C1780-18a Standard Practice for Installation Methods for Adhered Manufactured Stone Masonry Veneer
- 2018 ASTM C1780-18 Standard Practice for Installation Methods for Adhered Manufactured Stone Masonry Veneer
- 2017 ASTM C1780-17 Standard Practice for Installation Methods for Adhered Manufactured Stone Masonry Veneer
- 2016 ASTM C1780-16a Standard Practice for Installation Methods for Adhered Manufactured Stone Masonry Veneer
- 2016 ASTM C1780-16 Standard Practice for Installation Methods for Adhered Manufactured Stone Masonry Veneer
- 2015 ASTM C1780-15a Standard Practice for Installation Methods for Adhered Manufactured Stone Masonry Veneer
- 2015 ASTM C1780-15 Standard Practice for Installation Methods for Adhered Manufactured Stone Masonry Veneer
- 2014 ASTM C1780-14 Standard Practice for Installation Methods for Adhered Manufactured Stone Masonry Veneer
- 2013 ASTM C1780-13 Standard Practice for Installation Methods for Adhered Manufactured Stone Masonry Veneer
