ASTM D3828-16a
Standard Test Methods for Flash Point by Small Scale Closed Cup Tester

Standard No.
ASTM D3828-16a
Release Date
2016
Published By
American Society for Testing and Materials (ASTM)
Status
Replace By
ASTM D3828-16a(2021)
Latest
ASTM D3828-16a(2021)
Scope

5.1 Flash point measures the response of the test specimen to heat and ignition source under controlled laboratory conditions. It is only one of a number of properties that must be considered in assessing the overall flammability hazard of a material.

5.2 Flash point is used in shipping and safety regulations to define flammable and combustible materials and classify them. Consult the particular regulation involved for precise definitions of these classes.

5.3 Flash point can indicate the possible presence of highly volatile and flammable materials in a relatively nonvolatile or nonflammable material.

5.4 These test methods use a smaller sample (28201;mL to 48201;mL) and a shorter test time (18201;min to 28201;min) than traditional test methods.

5.5 Method A, IP 524 and EN ISO 3680 are similar methods for flash no-flash tests. Method B, IP 523 and EN ISO 3679 are similar methods for flash point determination.

1.1 These test methods cover procedures for flash point tests, within the range of –308201;°C to 3008201;°C, of petroleum products and biodiesel liquid fuels, using a small scale closed cup tester. The procedures may be used to determine, whether a product will or will not flash at a specified temperature (flash/no flash Method A) or the flash point of a sample (Method B). When used in conjunction with an electronic thermal flash detector, these test methods are also suitable for flash point tests on biodiesels such as fatty acid methyl esters (FAME).

1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.3 This standard should be used to measure and describe the properties of materials, products, or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Warning statements appear throughout. See also the Material Safety Data Sheets for the product being tested.

ASTM D3828-16a Referenced Document

  • ASTM D3941 Standard Test Method for Flash Point by the Equilibrium Method With a Closed-Cup Apparatus
  • ASTM D4057 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
  • ASTM D4177 Standard Practice for Automatic Sampling of Petroleum and Petroleum Products
  • ASTM D6299 Standard Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measurement System Performance
  • ASTM D6708 Standard Practice for Statistical Assessment and Improvement of Expected Agreement Between Two Test Methods that Purport to Measure the Same Property of a Material
  • ASTM E1137/E1137M Standard Specification for Industrial Platinum Resistance Thermometers
  • ASTM E300 Standard Practice for Sampling Industrial Chemicals

ASTM D3828-16a history

  • 2021 ASTM D3828-16a(2021) Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
  • 2016 ASTM D3828-16a Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
  • 2016 ASTM D3828-16 Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
  • 2012 ASTM D3828-12a Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
  • 2012 ASTM D3828-12 Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
  • 2009 ASTM D3828-09 Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
  • 2007 ASTM D3828-07a Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
  • 2007 ASTM D3828-07 Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
  • 2005 ASTM D3828-05 Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
  • 2002 ASTM D3828-02 Standard Test Methods for Flash Point by Small Scale Closed Cup Tester
  • 1998 ASTM D3828-98 Standard Test Methods for Flash Point by Small Scale Closed Tester
  • 1997 ASTM D3828-97 Standard Test Methods for Flash Point by Small Scale Closed Tester
Standard Test Methods for Flash Point by Small Scale Closed Cup Tester



Copyright ©2024 All Rights Reserved