ASTM D6699-16
Standard Practice for Sampling Liquids Using Bailers

Standard No.

ASTM D6699-16

Release Date

2016

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM D6699-16

Scope

5.1 A bailer is a device for obtaining a sample from stratified or un-stratified waters and liquid wastes. The most common use of a bailer is for sampling ground water from single-screened wells (Fig. 1) and well clusters (see Guide D4448).

5.2 This practice is applicable to sampling water and liquid wastes. The sampling procedure will depend on sampling plan and the data quality objectives (DQOs) (Practice D5792).

5.3 Bailers may be used to sample waters and liquid wastes in underground and above ground tanks and surface impoundments. However, the design of the unit and associated piping should be well understood so that the bailer can access the desired compartment and depth. Any stratification of the liquid should be identified prior to sampling.

Note 1: Viscous liquids and suspended solids may interfere with a bailer's designed operation.

5.4 Bailers do not subject the sample to pressure extremes. Bailing does disturb the water column and may cause changes to the parameters to be measured (for example, turbidity, gases, etc.).

5.5 The use of bailers in low flow wells for purging can result in increased agitation and turbidity in the sample and can introduce errors into the sample if the water surface level is drawn down below the top of the screen. In such cases, alternate methods of sampling such as Passive Sampling (Guide D7929) or Low Flow Sampling (Practice D6771) should be considered.

1.1 This practice covers the procedure for sampling stratified or un-stratified waters and liquid waste using bailers.

1.2 Three specific bailers are discussed in this practice. The bailers are the single and double check valve and differential pressure.

1.3 This standard does not cover all of the bailing devices available to the user. The bailers chosen for this practice are typical of those commercially available.

1.4 This practice should be used in conjunction with Guide D4687, Practice D5088, and Practice D5283.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM D6699-16 Referenced Document

• ASTM D4448 Standard Guide for Sampling Ground-Water Monitoring Wells
• ASTM D4687 Standard Guide for General Planning of Waste Sampling
• ASTM D5088 Standard Practice for Decontamination of Field Equipment Used at Nonradioactive Waste Sites
• ASTM D5283 Standard Practice for Generation of Environmental Data Related to Waste Management Activities: Quality Assurance and Quality Control Planning and Implementation
• ASTM D5681 Standard Terminology for Waste and Waste Management
• ASTM D5792 Standard Practice for Generation of Environmental Data Related to Waste Management Activities: Development of Data Quality Objectives
• ASTM D6051 Standard Guide for Composite Sampling and Field Subsampling for Environmental Waste Management Activities
• ASTM D6232 Standard Guide for Selection of Sampling Equipment for Waste and Contaminated Media Data Collection Activities
• ASTM D6517 Standard Guide for Field Preservation of Ground Water Samples
• ASTM D6564 Standard Guide for Field Filtration of Groundwater Samples
• ASTM D6634 Standard Guide for the Selection of Purging and Sampling Devices for Ground-Water Monitoring Wells
• ASTM D6771 Standard Practice for Low-Flow Purging and Sampling Used for Groundwater Monitoring
• ASTM D7929 Standard Guide for Selection of Passive Techniques for Sampling Groundwater Monitoring Wells

ASTM D6699-16 history

• 2016 ASTM D6699-16 Standard Practice for Sampling Liquids Using Bailers
• 2001 ASTM D6699-01(2010) Standard Practice for Sampling Liquids Using Bailers
• 2001 ASTM D6699-01(2006) Standard Practice for Sampling Liquids Using Bailers
• 2001 ASTM D6699-01 Standard Practice for Sampling Liquids Using Bailers