ASTM C1821/C1821M-16
Standard Practice for Installation of Underground Circular Precast Concrete Manhole Structures
- Standard No.
- ASTM C1821/C1821M-16
- Release Date
- 2016
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM C1821/C1821M-16(2021)e1
- Latest
- ASTM C1821/C1821M-16(2021)e1
- Scope
4.1 This practice is useful as a reference by an owner and/or the engineer in preparing project specifications.
4.2 The practice is useful as a reference by an owner, engineer, or installing contractor to properly install precast concrete circular manholes.
1.1 This practice covers the procedures to be followed in the planning, site preparation, installation, testing and backfilling of underground vertical reinforced circular precast concrete manholes and components manufactured in accordance with Specification C478 (C478M) and used in sewer, drainage, and water works.
1.2 Concrete pipe and box culverts are not covered under this practice. Also, precast concrete utility structures covered in Specification C858 are excluded from this practice.
1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM C1821/C1821M-16 Referenced Document
- ASTM C1107/C1107M Standard Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink)
- ASTM C1244 Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test Prior to Backfill
- ASTM C1244M Standard Test Method for Concrete Sewer Manholes by the Negative Air Pressure (Vacuum) Test (Metric)
- ASTM C1478 Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures, Pipes, and Laterals
- ASTM C1478M Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures, Pipes, and Laterals (Metric) (Withdrawn 2020)
- ASTM C443 Standard Specification for Joints for Circular Concrete Sewer and Culvert Pipe, Using Rubber Gaskets
- ASTM C443M Standard Specification for Joints for Circular Concrete Sewer and Culvert Pipe, Using Rubber Gaskets (Metric)
- ASTM C478 Standard Specification for Precast Reinforced Concrete Manhole Sections
- ASTM C478M Standard Specification for Precast Reinforced Concrete Manhole Sections [Metric]
- ASTM C822 Standard Terminology Relating to Concrete Pipe and Related Products
- ASTM C858 Standard Specification for Underground Precast Concrete Utility Structures
- ASTM C881/C881M Standard Specification for Epoxy-Resin-Base Bonding Systems for Concrete
- ASTM C923 Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals
- ASTM C923M Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals (Metric)
- ASTM C928/C928M Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs
- ASTM C969 Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines
- ASTM C969M Standard Practice for Infiltration and Exfiltration Acceptance Testing of Installed Precast Concrete Pipe Sewer Lines (Metric)
- ASTM C990 Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
- ASTM C990M Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants (Metric)
- ASTM D2487 Standard Test Method for Classification Of Soils For Engineering Purposes
- ASTM D2488 Recommended Practice for Description Of Soils (Visual-Manual Procedure)
- ASTM F2510/F2510M Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated Dual- and Triple-Wall Polyethylene and Polypropylene Pipes
ASTM C1821/C1821M-16 history
- 2021 ASTM C1821/C1821M-16(2021)e1 Standard Practice for Installation of Underground Circular Precast Concrete Manhole Structures
- 2016 ASTM C1821/C1821M-16 Standard Practice for Installation of Underground Circular Precast Concrete Manhole Structures
