ASTM D4800-94(2015)
Standard Guide for Classifying and Specifying Adhesives
- Standard No.
- ASTM D4800-94(2015)
- Release Date
- 1994
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D4800-94(2023)
- Latest
- ASTM D4800-94(2023)
- Scope
4.1 The purpose of this classification system is to provide a method of identifying adhesives in order to give industry a system that can be used universally for materials. It further provides a means for specifying these materials by the use of the standards that are developed using this guide.
4.2 This classification system was developed to permit the addition of future adhesives.
1.1 This guide provides a classification system for tabulating the properties of adhesives suitable for holding parts or assemblies together. The use of this guide also provides information necessary for the development of standard specifications for adhesives.
Note 1: This classification system may serve many of the needs of industries using adhesives. This guide is subject to revision as the need requires; therefore, the latest revision should always be used.
1.2 Limitations—This classification system is intended to be a means of identifying adhesives. It is not intended for the selection of materials. Material selection should be made by those having expertise in the adhesives field after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the attachment process to be employed, the inherent properties of the material not covered in this document, and the economic factors.
1.3 This classification system is based on the premise that adhesives can be arranged into broad generic families using basic properties to arrange the materials into groups, classes, and grades.
1.4 In all cases where the provisions of this classification system would conflict with the referenced ASTM specification for a particular material, the latter shall take precedence.
1.5 The values stated in SI units, as detailed in IEEE/ASTM SI 10, are to be regarded as the standard.
ASTM D4800-94(2015) Referenced Document
- ASTM D1084 Standard Test Methods for Viscosity of Adhesives*， 1997-04-20 Update
- ASTM D1298 Standard Test Method for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method*， 1999-04-20 Update
- ASTM D1310 Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus
- ASTM D2240 Standard Test Method for Properties of Rubber &8212; Durometer Hardness*， 2024-04-20 Update
- ASTM D2583 Standard Test Method for Indentation Hardness of Rigid Plastics by Means of a Barcol Impressor*， 2001-10-10 Update
- ASTM D2834 Standard Test Method for Nonvolatile Matter (Total Solids) in Water-Emulsion Floor Polishes, Solvent-Based Floor Polishes, and Polymer-Emulsion Floor Polishes*， 2022-12-01 Update
- ASTM D3278 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus*， 1996-04-20 Update
- ASTM D4562 Standard Test Method for Shear Strength of Adhesives Using Pin-and-Collar Specimen
- ASTM D5363 Standard Specification for Anaerobic Single-Component Adhesives (AN)*， 1997-04-20 Update
- ASTM D907 Standard Terminology of Adhesives*， 2023-05-16 Update
- IEEE/ASTM SI 10 American National Standard for Metric Practice
ASTM D4800-94(2015) history
- 2023 ASTM D4800-94(2023) Standard Guide for Classifying and Specifying Adhesives
- 1994 ASTM D4800-94(2015) Standard Guide for Classifying and Specifying Adhesives
- 1994 ASTM D4800-94(2011) Standard Guide for Classifying and Specifying Adhesives
- 1994 ASTM D4800-94(2005) Standard Guide for Classifying and Specifying Adhesives
- 1994 ASTM D4800-94(1999) Standard Guide for Classifying and Specifying Adhesives
