ASTM D7553-15
Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide

Standard No.

ASTM D7553-15

Release Date

2015

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM D7553-15(2021)

Latest

ASTM D7553-15(2021)

Scope

4.1 This test method is a measure of the solubility of asphalt in n-propyl bromide. The portion that is soluble in n-propyl bromide represents the active cementing constituents.

Note 2: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely assure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of these factors.

1.1 This test method covers the determination of the degree of solubility in n-propyl bromide of asphalt materials. It is intended to be a replacement for Test Method D2042 specifying a solvent that, like trichloroethylene, is safe in that it has no flash point, and has similar solubilizing characteristics to trichloroethylene, but it is not considered to be an ozone depleter banned by the Kyoto Protocol.

Note 1: This method is not applicable to tars and their distillation residues or highly cracked petroleum products. For methods covering tars, pitches, and other highly cracked petroleum products, and the use of other solvents, see Test Methods D4, D2318, and D2764.

1.2 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precaution statements are given in Section 7.

ASTM D7553-15 Referenced Document

• ASTM D2042 Standard Test Method for Solubility of Asphalt Materials in Trichloroethylene
• ASTM D2318 Standard Test Method for Quinoline-Insoluble (QI) Content of Tar and Pitch
• ASTM D2764 Standard Test Method for Dimethylformamide-Insoluble (DMF-I) Content of Tar and Pitch
• ASTM D3666 Standard Specification for Minimum Requirements for Agencies Testing and Inspecting Road and Paving Materials*， 2024-04-20 Update
• ASTM D4 Standard Test Method for Bitumen Content
• ASTM D6368 Standard Specification for Vapor-Degreasing Solvents Based on normal-Propyl Bromide and Technical Grade normal-Propyl Bromide
• ASTM E177 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
• ASTM E691 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

ASTM D7553-15 history

• 2021 ASTM D7553-15(2021) Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide
• 2015 ASTM D7553-15 Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide
• 2010 ASTM D7553-10 Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide
• 2009 ASTM D7553-09 Standard Test Method for Solubility of Asphalt Materials in N-Propyl Bromide