PD CEN/TS 1948-5:2015
Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs - Part 5: Long-term sampling of PCDDs/PCDFs and PCBs

Standard No.

PD CEN/TS 1948-5:2015

Release Date

2015

Published By

European Committee for Standardization (CEN)

Latest

PD CEN/TS 1948-5:2015

Replace

FprCEN/TS 1948-5-2014

Scope

This Technical Specification specifies the long-term sampling of PCDDs, PCDFs and PCBs. There are three different sampling methods, which use the three different principles described in EN 1948-1 modified for long-term sampling requirements: - filter/condenser method; - dilution method; - cooled probe method. Each sampling method is illustrated in detail in Annex D. The sampling methods described in this document are designed for a sampling duration of typically four weeks. Additionally this document specifies a framework of quality control requirements for any long-term sampling method to be applied. With the methods described experiences were gained for a concentration range from typically 0,003 ng I-TEQ/m 3 up to 4,0 ng I-TEQ/m 3 and 0,003 ng WHO-TEQ/m 3 up to 4,0 ng WHO-TEQ/m 3 respectively at different stationary sources (e. g. waste incinerators, sinter plants, cement kilns). For the complete measurement method the use of EN 1948-2 and EN 1948-3 describing extraction and clean-up and identification and quantification, respectively, is necessary in order to determine PCDDs/PCDFs. Also EN 1948-4 is necessary for the analyses of dioxin-like PCBs.

PD CEN/TS 1948-5:2015 Referenced Document

• EN 13284-1:2001 Stationary Source Emissions - Determination of Low Range Mass Concentration of Dust - Part 1: Manual Gravimetric Method*， 2024-04-20 Update
• EN 14181:2014 Stationary source emissions - Quality assurance of automated measuring systems
• EN 15259:2007 Air quality - Measurement of stationary source emissions - Requirements for measurement sections and sites and for the measurement objective, plan and report*， 2024-04-20 Update
• EN 15267-3:2007 Air quality - Certification of automated measuring systems - Part 3: Performance criteria and test procedures for automated measuring systems for monitoring emissions from stationary sources*， 2024-04-20 Update
• EN 1948-1:2006 Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs - Part 1: Sampling of PCDDs/PCDFs
• EN 1948-2:2006 Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs - Part 2: Extraction and clean-up of PCDDs/PCDFs
• EN 1948-3:2006 Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs - Part 3: Identification and quantification of PCDDs/PCDFs
• EN ISO 14956:2002 Air quality - Evaluation of the suitability of a measurement procedure by comparison with a required measurement uncertainty ISO 14956: 2002
• EN ISO 16911-1:2013 Stationary source emissions - Manual and automatic determination of velocity and volume flow rate in ducts - Part 1: Manual reference method
• EN ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories (ISO/IEC 17025:2005)
• ISO/IEC Guide 99:2007 International vocabulary of metrology - Basic and general concepts and associated terms (VIM)
• VDI 2066 Blatt 10-2004 Particulate matter measurement - Dust measurement in flowing gases - Measurement of PM10 and PM2,5 emissions at stationary sources by impaction method

PD CEN/TS 1948-5:2015 history

• 2015 PD CEN/TS 1948-5:2015 Stationary source emissions - Determination of the mass concentration of PCDDs/PCDFs and dioxin-like PCBs - Part 5: Long-term sampling of PCDDs/PCDFs and PCBs