ASTM F1545-15a
Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges

Standard No.
ASTM F1545-15a
Release Date
2015
Published By
American Society for Testing and Materials (ASTM)
Status
Replace By
ASTM F1545-15a(2021)
Latest
ASTM F1545-15a(2021)
Scope

1.1 This specification covers factory-made plastic-lined ferrous metal pipe, fittings, and flanges intended primarily for conveying corrosive fluids. Requirements for materials, workmanship, dimensions, design, fabrication, working pressure and temperatures, test methods, qualification requirements, and markings are included.

1.1.1 This specification does not define the suitability of different liner materials to various chemical and operating environments. Refer to the manufacturer's chemical resistance data for suitability recommendations.

1.1.2 This specification does not include products coated with plastics.

1.2 This specification covers plastic-lined pipe, flanges, and fittings as listed in Table 1. Pressure limitations shall be in accordance with ASME B16 Standards, except reduced pressure limitations may be established by the manufacturer, considering both pressure and temperature limitations of the ferrous metal housing and the sealing ability of the liner.

Note 1: In this specification, propylene plastics cover those materials defined as both polypropylene plastics and propylene plastics in Terminology F412. Both materials are identified as “PP” on the product. Note that this is at variance with Terminology D1600, where “PP” is the abbreviation for polypropylene.

1.3 The plastic-lined flanged pipe and fitting assemblies are limited to temperatures shown in Table 2. End users should consult with manufacturers as to the likely result of using a particular lined piping component at temperatures below the rated minimum.

Note 2: The temperature limitations are based on noncorrosive test conditions. Use in specific aggressive environments may alter temperature limitations. In such instances, specific temperature limits shall be established by mutual agreement between the purchaser and the manufacturer.

(A) Storage or handling below 20°F (−7°C) of uninstalled 4, 6, and 8-in. components should be avoided. Check flange face ‘cold-flow’ modulus, and check chemical compatibility at all expected operating temperatures

1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applica......

ASTM F1545-15a Referenced Document

  • ASTM A105/A105M Standard Specification for Carbon Steel Forgings for Piping Applications
  • ASTM A106/A106M Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service
  • ASTM A126 Standard Specification for Gray Iron Castings for Valves, Flanges, and Pipe Fittings
  • ASTM A135/A135M Standard Specification for Electric-Resistance-Welded Steel Pipe*， 2024-04-20 Update
  • ASTM A182/A182M Standard Specification for Forged or Rolled Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service
  • ASTM A216/A216M Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High- Temperature Service
  • ASTM A234/A234M Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service
  • ASTM A278/A278M Standard Specification for Gray Iron Castings for Pressure-Containing Parts for Temperatures Up to 650 °F (350 °C)
  • ASTM A312/A312M Standard Specification for Seamless and Welded Austenitic Stainless Steel Pipes
  • ASTM A351/A351M Standard Specification for Castings, Austenitic, Austenitic- Ferritic (Duplex), for Pressure-Containing Parts
  • ASTM A395/A395M Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures
  • ASTM A403/A403M Standard Specification for Wrought Austenitic Stainless Steel Piping Fittings
  • ASTM A48/A48M Standard Specification for Gray Iron Castings
  • ASTM A513/A513M Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing
  • ASTM A53/A53M Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless
  • ASTM A536 Standard Specification for Ductile Iron Castings
  • ASTM A587 Standard Specification for Electric-Resistance-Welded Low-Carbon Steel Pipe for the Chemical Industry
  • ASTM D1457 Standard Specification for PTFE Molding and Molding and Extrusion Materials
  • ASTM D1505 Standard Test Method for Density of Plastics by the Density-Gradient Technique
  • ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
  • ASTM D2116 Standard Specification for FEP-Fluorocarbon Molding and Extrusion Materials
  • ASTM D3159 Standard Specification for Modified ETFE-Fluoropolymer Molding and Extrusion Materials
  • ASTM D3222 Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials
  • ASTM D3307 Standard Specification for Perfluoroalkoxy (PFA) Resin Molding and Extrusion Materials
  • ASTM D3350 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials*， 2024-04-20 Update
  • ASTM D4101 Standard Specification for Propylene Plastic Injection and Extrusion Materials
  • ASTM D4894 Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials
  • ASTM D4895 Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion
  • ASTM D5575 Standard Specification for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers
  • ASTM D729 Standard Practice for Verifying Vertical Inclinometer Probe Performance
  • ASTM D792 Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
  • ASTM F412 Standard Terminology Relating to Plastic Piping Systems
  • ASTM F714 Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter

ASTM F1545-15a history

  • 2021 ASTM F1545-15a(2021) Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges
  • 2015 ASTM F1545-15a Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges
  • 2015 ASTM F1545-15 Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges
  • 1997 ASTM F1545-97(2009) Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges
  • 1997 ASTM F1545-97(2003) Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges
  • 1997 ASTM F1545-97e1 Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges
  • 1997 ASTM F1545-97 Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges
Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges


Copyright ©2024 All Rights Reserved