ASTM C990-09(2014)
Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
- Standard No.
- ASTM C990-09(2014)
- Release Date
- 2009
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM C990-09(2019)
- Latest
- ASTM C990-09(2019)
- Scope
1.1 This specification covers joints for precast concrete pipe and box, and other sections using preformed flexible joint sealants for use in storm sewers and culverts which are not intended to operate under internal pressure, or are not subject to infiltration or exfiltration limits. Joint material used in horizontal applications is intended to prevent the flow of solids through the joint.
1.2 For precast concrete manhole sections and other vertical structures, which are subject to internal or external pressure, infiltration or exfiltration limits are not prohibited from being specified. Joints in vertical structures covered by this specification are intended mainly to prevent the flow of solids or fluids through the joint.
1.3 This specification is to be used with pipe and structures conforming in all respects to Specifications C14, C76, C478, C506, C507, C655, C985, C1433, C1504, and C1577, provided that if there is a conflict in permissible variations in dimensions, the requirements of this specification shall govern.
1.4 This specification is the inch-pound companion to C990M; therefore, no SI equivalents are presented in the specification.
Note 1—This specification covers the material and performance of the joint and sealant only. Infiltration and exfiltration quantities for installed sections are dependent on factors other than the joints which must be covered by other specifications and suitable testing of the installed pipeline.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM C990-09(2014) Referenced Document
- ASTM C14 Standard Specification for Concrete Sewer, Storm Drain, and Culvert Pipe
- ASTM C1433 Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers
- ASTM C1504 Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains
- ASTM C1577 Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers Designed According to AASHTO LRFD
- ASTM C478 Standard Specification for Precast Reinforced Concrete Manhole Sections
- ASTM C506 Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe
- ASTM C507 Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe
- ASTM C655 Standard Specification for Reinforced Concrete D-Load Culvert,Storm Drain, And Sewer Pipe
- ASTM C76 Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe
- ASTM C822 Standard Terminology Relating to Concrete Pipe and Related Products
- ASTM C972 Standard Test Method for Compression-Recovery of Tape Sealant
- ASTM C985 Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe
- ASTM D113 Standard Test Method for Ductility of Bituminous Materials
- ASTM D217 Standard Test Methods for Cone Penetration of Lubricating Grease
- ASTM D297 Standard Test Methods for Rubber Products-Chemical Analysis
- ASTM D36 Standard Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)
- ASTM D4 Standard Test Method for Bitumen Content
- ASTM D6 Standard Test Method for Loss on Heating of Oil and Asphaltic Compounds
- ASTM D71 Standard Test Method for Relative Density of Solid Pitch and Asphalt (Displacement Method)
- ASTM D92 Standard Test Method for Flash and Fire Points by Cleveland Open Cup
ASTM C990-09(2014) history
- 2019 ASTM C990-09(2019) Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
- 2009 ASTM C990-09(2014) Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
- 2009 ASTM C990-09 Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
- 2008 ASTM C990-08 Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
- 2006 ASTM C990-06 Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
- 2003 ASTM C990-03a Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
- 2003 ASTM C990-03 Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
- 2001 ASTM C990-01a Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
- 2001 ASTM C990-01 Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
- 2000 ASTM C990-00 Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants
