ASTM D2166/D2166M-13
Standard Test Method for Unconfined Compressive Strength of Cohesive Soil

Standard No.

ASTM D2166/D2166M-13

Release Date

2013

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM D2166/D2166M-16

Latest

ASTM D2166/D2166M-16

Scope

5.1 The primary purpose of the unconfined compression test is to quickly obtain a measure of compressive strength for those soils that possess sufficient cohesion to permit testing in the unconfined state.

5.2 Samples of soils having slickensided or fissured structure, samples of some types of loess, very soft clays, dry and crumbly soils and varved materials, or samples containing significant portions of silt or sand, or both (all of which usually exhibit cohesive properties), frequently display higher shear strengths when tested in accordance with Test Method D2850. Also, unsaturated soils will usually exhibit different shear strengths when tested in accordance with Test Method D2850.

5.3 If tests on the same sample in both its intact and remolded states are performed, the sensitivity of the material can be determined. This method of determining sensitivity is suitable only for soils that can retain a stable specimen shape in the remolded state.

Note 2—For soils that will not retain a stable shape, a vane shear test or Test Method D2850 can be used to determine sensitivity.

Note 3—The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D3740 are generally considered capable of competent and objective testing/sampling/inspection. Users of this standard are cautioned that compliance with Practice D3740 does not in itself ensure reliable results. Reliable results depend on many factors; Practice D3740 provides a means of evaluating some of those factors.

1.1 This test method covers the determination of the unconfined compressive strength of cohesive soil in the intact, remolded, or reconstituted condition, using strain-controlled application of the axial load.

1.2 This test method provides an approximate value of the strength of cohesive soils in terms of total stresses.

1.3 This test method is applicable only to cohesive materials which will not expel or bleed water (water expelled from the soil due to deformation or compaction) during the loading portion of the test and which will retain intrinsic strength after removal of confining pressures, such as clays or cemented soils. Dry and crumbly soils, fissured or varved materials, silts, peats, and sands cannot be tested with this method to obtain valid unconfined compression strength values.

Note 1—The determination of the unconsolidated, undrained strength of cohesive soils with lateral confinement is covered by Test Method D2850.

1.4 This test method is not a substitute for Test Method D2850.

1.5 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this standard.

1.5.1 The procedures used to specify how data are collected/recorded and calculated in this test method are regarded as the industry standard. In addition, they are representative of the significant digits that should generally be retained. The procedur......

ASTM D2166/D2166M-13 history

• 2016 ASTM D2166/D2166M-16 Standard Test Method for Unconfined Compressive Strength of Cohesive Soil
• 2013 ASTM D2166/D2166M-13 Standard Test Method for Unconfined Compressive Strength of Cohesive Soil
• 2006 ASTM D2166-06 Standard Test Method for Unconfined Compressive Strength of Cohesive Soil
• 2000 ASTM D2166-00e1 Standard Test Method for Unconfined Compressive Strength of Cohesive Soil
• 2000 ASTM D2166-00 Standard Test Method for Unconfined Compressive Strength of Cohesive Soil