ASTM C449-07(2013)
Standard Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement
- Standard No.
- ASTM C449-07(2013)
- Release Date
- 2007
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM C449-07(2019)
- Latest
- ASTM C449-07(2019)
- Scope
1.1 This specification covers mineral fiber (rock or slag) insulating and finishing cement shipped in dry-mix form, including hydraulic-setting binder, which, when mixed with water and applied in accordance with the manufacturer's directions, affords a smooth surface as a final finish for heated surfaces up to 12008201;°F (6498201;°C) for specific applications. The actual temperature limit shall be agreed upon between the purchaser and the manufacturer.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazards caveat pertains only to the test method (Section 10) described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4 When the installation or use of thermal insulation materials, accessories, and systems pose safety or health problems, the manufacturer shall provide the user with appropriate current information regarding any known problems associated with the recommended use of the company's products and shall also recommend protective measures to be employed in their safe utilization. The user shall establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
ASTM C449-07(2013) Referenced Document
- ASTM C1045 Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions
- ASTM C1058 Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation
- ASTM C1114 Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus
- ASTM C163 Standard Practice for Mixing Thermal Insulating Cement Samples
- ASTM C166 Standard Test Method for Covering Capacity and Volume Change Upon Drying of Thermal Insulating Cement
- ASTM C168 Standard Terminology Relating to Thermal Insulation
- ASTM C177 Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus
- ASTM C356 Standard Test Method for Linear Shrinkage of Preformed High-Temperature Thermal Insulation Subjected to Soaking Heat
- ASTM C390 Standard Criteria for Sampling and Acceptance of Preformed Thermal Insulation Lots
- ASTM C411 Standard Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation
- ASTM C518 Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus
- ASTM C795 Standard Specification for Thermal Insulation for Use in Contact with Austenitic Stainless Steel
- ASTM E136 Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750oC
ASTM C449-07(2013) history
- 2019 ASTM C449-07(2019) Standard Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement
- 2007 ASTM C449-07(2013) Standard Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement
- 2007 ASTM C449-07 Standard Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement
- 2000 ASTM C449/C449M-00 Standard Specification for Mineral Fiber Hydraulic-Setting Thermal Insulating and Finishing Cement
