SAE AMS3277G-2012
Sealing Compound, Polythioether Rubber, Fast Curing for Integral Fuel Tanks and General Purpose, Intermittent Use to 360°F (182°C)

Standard No.

SAE AMS3277G-2012

Release Date

2012

Published By

Society of Automotive Engineers (SAE)

Status

Be replaced 2015-12

Replace By

SAE AMS3277H-2014

Latest

SAE AMS3277K-2019

Scope

This specification covers polythioether rubber fuel resistant sealing compounds supplied as a two component system which cures at room temperature. This product has been used in aircraft integral fuel tanks for repair of fillet and fastener seals and faying surface seals as well as initial sealing of faying surfaces, overcoating of fasteners, and sealing of seams and joints, for service from -80 to +320°F (-62 to +160°C), with short-term recurring exposures (approximately six hours) up to 360°F (182°C), but usage is not limited to such applications. This product is not recommended for use on aircraft windshields or canopies or other applications where crazi

SAE AMS3277G-2012 Referenced Document

• PRI Public Switched Telephone Network (PSTN); Terminals for Low Bit-Rate Multimedia Communication
• SAE AMS-C-27725-1999 Coating@ Corrosion Preventative@ Polyurethane for Aircraft Integral Fuel Tanks for Use to 250 Degrees F (121 Degrees C) (FSC 8030)
• SAE AMS2471 ANODIC TREATMENT FOR ALUMINUM BASE ALLOYS Sulfuric Acid Process
• SAE AMS2629 JET REFERENCE FLUID
• SAE AMS3020-1978 "Oil@ Reference@ for ""L"" Stock Rubber Testing"
• SAE AMS3021 REFERENCE FLUID FOR TESTING DI-ESTER (POLYOL) RESISTANT MATERIAL
• SAE AMS3276 Sealing Compound@ Integral Fuel Tanks and General Purpose@ Intermittent Use to 360 Degrees F (182 Degrees C)
• SAE AMS4045 ALUMINUM ALLOT SHEET AND PLATE 5.6Zn - 2.5Mg - 1.6Cu - 0.25Cr (75S-T6)
• SAE AMS4901 TITANIUM SHEET AND STRIP Annealed - 70,000 psi Yield
• SAE AMS5516 STEEL SHEET AND STRIP, CORROSION RESISTANT 18 Chromium - 8 Nickel (Cold Rolled)
• SAE AS5127-1997 Methods for Testing Aerospace Sealants
• SAE AS5127/1-1997 Test Methods for Aerospace Sealants Two-Component Synthetic Rubber Compounds
• SAE AS5502-2000 Standard Requirements for Aerospace Sealants

SAE AMS3277G-2012 history

• 2019 SAE AMS3277K-2019 Sealing Compound, Polythioether Rubber Fast Curing for Integral Fuel Tanks and General Purpose, Intermittent Use to 360 °F (182 °C)
• 2015 SAE AMS3277J-2015 Sealing Compound, Polythioether Rubber, Fast Curing for Integral Fuel Tanks and General Purpose, Intermittent Use to 360°F (182°C)
• 2014 SAE AMS3277H-2014 Sealing Compound@ Polythioether Rubber Fast Curing for Integral Fuel Tanks and General Purpose@ Intermittent Use to 360 °F (182 °C)
• 2012 SAE AMS3277G-2012 Sealing Compound, Polythioether Rubber, Fast Curing for Integral Fuel Tanks and General Purpose, Intermittent Use to 360°F (182°C)
• 2010 SAE AMS3277F-2010 Sealing Compound, Polythioether Rubber, Fast Curing for Integral Fuel Tanks and General Purpose, Intermittent Use to 360F (182C)
• 2010 SAE AMS3277E-2010 Sealing Compound, Polythioether Rubber, Fast Curing Integral Fuel Tanks and General Purpose, Intermittent Use to 360°F (182°C)
• 2007 SAE AMS3277D-2007 Sealing Compound@ Polythioether Rubber Fast Curing for Integral Fuel Tanks and General Purpose@ Intermittent Use to 400 °F (204 °C)
• 2004 SAE AMS3277C-2004 Sealing Compound, Polythioether Rubber, Fast Curing Integral Fuel Tanks and General Purpose, Intermittent Use to 400°F (204°C)
• 2002 SAE AMS3277B-2002 (R) Sealing Compound, Polythioether Rubber Fuel Resistant, Fast Curing Intermittent Use to 360 °F (182 °C)
• 1999 SAE AMS3277A-1999 Sealing Compound@ Polythioether Integral Fuel Tanks and General Purpose@ Fast Curing Intermittent Use to 360 Degrees F (182 Degrees C)
• 1995 SAE AMS3277-1995 Sealing Compound@ Polythioether Integral Fuel Tanks and General Purpose@ Fast Curing Intermittent Use to 360 Degrees F (182 Degrees C)