ASTM D2257-98(2012)
Standard Test Method for Extractable Matter in Textiles

Standard No.
ASTM D2257-98(2012)
Release Date
1998
Published By
American Society for Testing and Materials (ASTM)
Status
Replace By
ASTM D2257-20
Latest
ASTM D2257-20
Scope

This test method may be used for acceptance testing of commercial shipments.

In case of a dispute arising from differences in reported test results using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between the laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens which are as homogeneous as possible and which are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using appropriate statistical analysis and a probability level chosen by the two parties before the testing begins. If a bias is found, either its cause must be found and corrected, or the purchaser and supplier must agree to interpret future test results with consideration to the known bias.

This test method is used for the determination of the amounts of naturally present oily or waxy impurities that have not been completely removed from textiles made from animal fibers, and for the determination of the amounts of oily or waxy finishing materials applied to raw materials or textiles during manufacture. See 3.1.1, extractable matter.

The test method may be used as a step in the determination of the commercial weight of fiber, yarn, and textile shipments.

The International Wool Textile Organization specifies the use of a halogenated hydrocarbon, dichloromethane, also called methylene chloride (CH2Cl2) instead of the solvent specified in this test method (IWTO-10-62(E)).

Extractables by mass loss is frequently used for textiles which have a relatively large amount of extractable material to effect a significant mass change.

1.1 This test method covers a procedure for determining the extractable material on most fibers, yarns, and fabrics. Three options are included. Option 1 uses heat and Soxhlet extraction apparatus. Option 2 uses room temperature and extraction funnels. Option 3 uses either Option 1 or Option 2 extraction but provides for calculation of extractable matter from the loss in mass of the material due to the extraction rather than the extractable matter residue.

Note 18212;Other standards for the determination of extractable matter in textiles made of specific fibers include: Specification , Specification , and Test Method D1574.

1.1.1 The solvents for use in this method are any solvents that the party or parties concerned agreed on; such as, Halogenated Hydrocarbon (HH) chloroform, tetrachloroethane, alcohol.

1.1.2 This test method may not extract cross-linked finishes or resins which may be on the textile.

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Sections 6 and 7.

ASTM D2257-98(2012) Referenced Document

  • ASTM D123 Standard Terminology Relating to Textiles*， 2023-09-14 Update
  • ASTM D1574 Standard Test Method for Extractable Matter in Wool and Other Animal Fibers
  • ASTM D1909 Standard Table of Commercial Moisture Regains for Textile Fibers
  • ASTM D2258 Standard Practice for Sampling Yarn for Testing*， 1999-04-19 Update
  • ASTM D3333 Standard Practice for Sampling Manufactured Staple Fibers, Sliver, or Tow for Testing
  • ASTM D4920 Standard Terminology Relating to Moisture in Textiles
  • ASTM D541 Specification for Single Jute Yarn
  • ASTM D681 Standard test method for accelerated temperature aging of printing and writing papers using oven exposure apparatus

ASTM D2257-98(2012) history

Standard Test Method for Extractable Matter in Textiles


Copyright ©2024 All Rights Reserved