ASTM E139-11
Standard Test Methods for Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials

Standard No.

ASTM E139-11

Release Date

2011

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM E139-11(2018)

Latest

ASTM E139-11(2018)

Scope

Rupture tests, properly interpreted, provide a measure of the ultimate load-carrying ability of a material as a function of time. Creep tests measure the load-carrying ability for limited deformations. The two tests complement each other in defining the load-carrying ability of a material. In selecting material and designing parts for service at elevated temperatures, the type of test data used will depend on the criterion of load-carrying ability that better defines the service usefulness of the material.

1.1 These test methods cover the determination of the amount of deformation as a function of time (creep test) and the measurement of the time for fracture to occur when sufficient force is present (rupture test) for materials when under constant tensile forces at constant temperature. It also includes the essential requirements for testing equipment. For information of assistance in determining the desirable number and duration of tests, reference should be made to the product specification.

1.2 These test methods list the information which should be included in reports of tests. The intention is to ensure that all useful and readily available information is transmitted to interested parties. Reports receive special attention for the following reasons: (1) results from different, recognized procedures vary significantly; therefore, identification of methods used is important; (2) later studies to establish important variables are often hampered by the lack of detailed information in published reports; (3) the nature of prolonged tests often makes retest impractical, and at the same time makes it difficult to remain within the recommended variations of some controlled variables. A detailed report permits transmittal of test results without implying a degree of control which was not achieved.

1.3 Tests on notched specimens are not included. These tests are addressed in Practice E292.

1.4 Tests under conditions of short times are not included. These test methods are addressed in Test Methods E21.

1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. ^REFERENCE:

ASTM Standards:

E4 Practices for Force Verification of Testing Machines

E6 Terminology Relating to Methods of Mechanical Testing

E8 Test Methods for Tension Testing of Metallic Materials

E21 Test Methods for Elevated Temperature Tension Tests of Metallic Materials

E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

E74 Practice of Calibration of Force-Measuring Instruments for Verifying the Forc......

ASTM E139-11 Referenced Document

• ASTM E1012 Standard Practice for Verification of Specimen Alignment Under Tensile Loading
• ASTM E177 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
• ASTM E21 Standard Test Methods for Elevated Temperature Tension Tests of Metallic Materials
• ASTM E220 Standard Test Method for Calibration of Thermocouples By Comparison Techniques
• ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
• ASTM E292 Standard Test Methods for Conducting Time-for-Rupture Notch Tension Tests of Materials
• ASTM E4 Standard Practices for Force Verification of Testing Machines
• ASTM E6 Standard Terminology Relating to Methods of Mechanical Testing
• ASTM E633 Standard Guide for Use of Thermocouples in Elevated-Temperature Mechanical Testing
• ASTM E74 Standard Practices for Calibration and Verification for Force-Measuring Instruments
• ASTM E8 Standard Test Methods for Tension Testing of Metallic Materials
• ASTM E83 Standard Practice for Verification and Classification of Extensometer

ASTM E139-11 history

• 2018 ASTM E139-11(2018) Standard Test Methods for Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials
• 2011 ASTM E139-11 Standard Test Methods for Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials
• 2006 ASTM E139-06 Standard Test Methods for Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials
• 2000 ASTM E139-00e1 Standard Test Methods for Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials
• 2000 ASTM E139-00 Standard Test Methods for Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials