- Standard No.
- BS EN 61000-6-3:2007+A1:2011
- Release Date
- 2007
- Published By
- British Standards Institution (BSI)
- Latest
-
BS EN 61000-6-3:2007+A1:2011
- Replace By
-
SY/T 6828-2017
- Replace
-
02/202317 DC-2002
BS EN 61000-6-3:2001
BS EN 61000-6-3:2007
- Scope
- This part of IEC 61000 for EMC emission requirements applies to electrical and electronic
apparatus intended for use in residential, commercial and light-industrial environments.
Emission requirements in the frequency range 0 Hz to 400 GHz are covered. No
measurement needs to be performed at frequencies where no requirement is specified.
This generic EMC emission standard is applicable if no relevant dedicated product or productfamily
EMC emission standard exists.
This standard applies to apparatus intended to be directly connected to a low-voltage public
mains network or connected to a dedicated DC source, which is intended to interface between
the apparatus and the low-voltage public mains network. This standard applies also to
apparatus which is battery operated or is powered by a non-public, but non-industrial, lowvoltage
power distribution system if this apparatus is intended to be used in the locations
described below.
The environments encompassed by this standard are residential, commercial and lightindustrial
locations, both indoor and outdoor. The following list, although not comprehensive,
gives an indication of locations that are included:
– residential properties, for example houses, apartments;
– retail outlets, for example shops, supermarkets;
– business premises, for example offices, banks;
– areas of public entertainment, for example cinemas, public bars, dance halls;
– outdoor locations, for example petrol stations, car parks, amusement and sports centres;
– light-industrial locations, for example workshops, laboratories, service centres.
Locations that are characterised by being supplied directly at low voltage from the public
mains network are considered to be residential, commercial or light-industrial.
The object of this standard is to define the emission test requirements for apparatus defined
in the scope in relation to continuous and transient, conducted and radiated disturbances.
The emission requirements have been selected so as to ensure that disturbances generated
by apparatus operating normally in residential, commercial and light-industrial locations do
not exceed a level which could prevent other apparatus from operating as intended. Fault
conditions of apparatus are not taken into account. Not all disturbance phenomena have been
included for testing purposes in this standard but only those considered as relevant for the
equipment covered by this standard. These requirements represent essential electromagnetic
compatibility emission requirements.
Requirements are specified for each port considered.
BS EN 61000-6-3:2007+A1:2011 Referenced Document
- CISPR 14-1-2005 Electromagnetic compatibility - Requirements for household appliances, electric tools and similar apparatus - Part 1: Emission
- CISPR 16-1-1-2010 Spécifications des méthodes et des appareils de mesure des perturbations radioélectriques et de l'immunité aux perturbations radioélectriques – Partie 1-1: Appareils de mesure des perturbations radioélectriques et de l'immunité aux perturbations radioélec*， 2010-01-01 Update
- CISPR 16-1-2-2003 Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-2:Radio disturbance and immunity measuring apparatus - Ancillary equipment - Conducted disturbances
- CISPR 16-1-4-2007 Specification for radio disturbance and immunity measuring apparatus and methods – Part 1-4: Radio disturbance and immunity measuring apparatus – Ancillary equipment – Radiated disturbances
- CISPR 16-2-1-2008 pecification for radio disturbance and immunity measuring apparatus and methods – Part 2-1: Methods of measurement of disturbances and immunity – Conducted disturbance measurements*， 2008-10-01 Update
- CISPR 16-2-3-2006 Specification for radio disturbance and immunity measuring apparatus and methods – Part 2-3: Methods of measurement of disturbances and immunity – Radiated disturbance measurements
- CISPR 16-4-2-2003 Specification for radio disturbance and immunity measuring apparatus and methods - Part 4-2:Uncertainties,statistics and limit modelling - Uncertainty in EMC measurements
- CISPR 22-2008 Information technology equipment – Radio disturbance characteristics – Limits and methods of measurement*， 2008-09-01 Update
BS EN 61000-6-3:2007+A1:2011 history
- 2007 BS EN 61000-6-3:2007+A1:2011 Electromagnetic compatibility (EMC). Generic standards. Emission standard for residential, commercial and light-industrial environments
- 2007 BS EN 61000-6-3:2007 Electromagnetic compatibility (EMC) - Generic standards - Emission standard for residential, commercial and light-industrial environments
- 2001 BS EN 61000-6-3:2001 Electromagnetic compatibility (EMC) - Generic standards - Emission standard for residential, commercial and light-industrial environments
BS EN 61000-6-3:2007+A1:2011 Electromagnetic compatibility (EMC). Generic standards. Emission standard for residential, commercial and light-industrial environments was changed to SY/T 6828-2017 Technical specification for oil and gas pipeline geological disaster risk management.