ASTM D3278-96(2011)
Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
- Standard No.
- ASTM D3278-96(2011)
- Release Date
- 1996
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D3278-20
- Latest
- ASTM D3278-21
- Scope
Flash point is one of the properties used to define the flammability of a liquid. It is used to classify liquids according to their flammability by governmental regulatory agencies. It may also be used to determine the presence of impurities or contaminants in a given liquid, such as the presence of residual solvents in solvent-refined drying oils. See Test Methods D56 and D93 for alternate flash point testing.
1.1 These test methods cover procedures for determining whether a material does or does not flash at a specified temperature or for determining the lowest finite temperature at which a material does flash when using a small scale closed-cup apparatus. The test methods are applicable to paints, enamels, lacquers, varnishes, and related products having a flash point between 0 and 110°C (32 and 230°F) and viscosity lower than 150 St at 25°C (77°F).
Note 18212;Tests at higher or lower temperatures are possible.
Note 28212;More viscous materials may be tested in accordance with Annex A4.
Note 38212;Organic peroxides may be tested in accordance with Annex A5, which describes the applicable safety precautions.
Note 48212;The U.S. Department of Labor (OSHA, Hazard Communications), the U.S. Department of Transportation (RSPA), and the U.S. Environmental Protection Agency (EPA) have specified Test Methods D3278 as one of several acceptable methods for the determination of flash point of liquids in their regulations.
Note 58212;These test methods are similar to International Standards ISO 3679 and ISO 3680.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard should be used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions and should not be used to describe or appraise the fire-hazard or fire-risk of materials, products, or assemblies under actual fire conditions. However, results of the test may be used as elements of a fire-hazard or a fire-risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard or fire risk of a particular end use.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see 8.1 and 11.2.
ASTM D3278-96(2011) Referenced Document
- ASTM D1015 Standard Test Method for Freezing Points of High-Purity Hydrocarbons*， 2004-05-01 Update
- ASTM D1078 Standard Test Method for Distillation Range of Volatile Organic Liquids*， 1999-04-19 Update
- ASTM D56 Standard Test Method for Flash Point by Tag Closed Tester
- ASTM D850 Standard Test Method for Distillation of Industrial Aromatic Hydrocarbons and Related Materials*， 1999-04-19 Update
- ASTM D93 Standard Test Methods for Flash-Point by Pensky-Martens Closed Cup Tester*， 1997-04-19 Update
- ISO 3679 Determination of flash point – Method for flash no-flash and flash point by small scale closed cup tester*， 2022-11-04 Update
- ISO 3680 Determination of flash/no flash - Rapid equilibrium closed cup method*， 2004-04-01 Update
ASTM D3278-96(2011) history
- 2021 ASTM D3278-21 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
- 2020 ASTM D3278-20 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
- 1996 ASTM D3278-96(2011) Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
- 1996 ASTM D3278-96(2004)e1 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
- 1996 ASTM D3278-96e1 Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
- 1982 ASTM D3278-82e1 Standard Test Methods for Flash Point of Liquids by Setaflash Closed-Cup Apparatus
