ASTM F355-10a
Standard Test Method for Impact Attenuation of Playing Surface Systems and Materials

Standard No.

ASTM F355-10a

Release Date

2010

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM F355-16

Latest

ASTM F355-23

Scope

The results of this method quantify the impact attenuation of playing surface and system specimens under the specific test conditions.

The test method measures the outcome of impacts performed under specific conditions. It does not quantify the intrinsic material properties of the tested specimens.

Test results from different specimens obtained under the same conditions (that is, the same missile mass and geometry, drop height, etc.) may be used to compare impact attenuation under those conditions.

Test results obtained under different conditions are not comparable. Specifically obtained with different missiles are not equivalent and cannot be directly compared. Similarly, test results obtained using the same missile, but using different drop heights, are not directly comparable.

1.1 This test method measures the impact attenuation of playing surface systems and materials, specifically the peak impact acceleration (“impact shock”) produced under prescribed impact conditions.

1.2 This test method is applicable to natural and artificial playing surface systems intended to provide impact attenuation, including natural and artificial turf sports fields and playground surfaces.

1.3 This test method is applicable to impact attenuating mats and padding used in sports facilities, including stadium wall padding, gymnastic mats and wrestling mats.

1.4 This test method may be used to measure the impact attenuation of materials and components used as protective padding on trampoline frames, goal posts, etc., provided the material or component can be tested separately from the equipment to which it is attached.

1.5 Without modifications, this test method shall not be used to test materials and components that are attached to structures or equipment or finished products, unless the impact attenuation of the whole system is of interest.

1.6 While it is widely believed that appropriate impact attenuation can reduce the risk of impact-related injuries, the relationships between the results of this test method and specific injury risk and outcomes have not been determined.

1.7 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F355-10a Referenced Document

• ASTM D1596 Standard Test Method for Dynamic Shock Cushioning Characteristics of Packaging Material
• ASTM E105 Standard Practice for Probability Sampling Of Materials
• ASTM E122 Standard Practice for Calculating Sample Size to Estimate, With a Specified Tolerable Error, the Average for Characteristic of a Lot or Process
• ASTM E691 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
• ASTM F1292 Standard Specification for Impact Attenuation of Surface Systems Under and Around Playground Equipment
• ASTM F2650 Standard Terminology Relating to Impact Testing of Sports Surfaces and Equipment*， 2024-04-19 Update
• SAE J211/1 Instrumentation for Impact Test Part 1 - Electronic Instrumentation

ASTM F355-10a history

• 2023 ASTM F355-23 Standard Test Method for Impact Attenuation of Playing Surface Systems, Other Protective Sport Systems, and Materials Used for Athletics, Recreation and Play
• 2016 ASTM F355-16e1 Standard Test Method for Impact Attenuation of Playing Surface Systems, Other Protective Sport Systems, and Materials Used for Athletics, Recreation and Play
• 2016 ASTM F355-16 Standard Test Method for Impact Attenuation of Playing Surface Systems, Other Protective Sport Systems, and Materials Used for Athletics, Recreation and Play
• 2010 ASTM F355-10a Standard Test Method for Impact Attenuation of Playing Surface Systems and Materials
• 2010 ASTM F355-10 Standard Test Method for Impact Attenuation of Playing Surface Systems and Materials
• 2009 ASTM F355-09 Standard Test Method for Impact Attenuation of Playing Surface Systems and Materials
• 2001 ASTM F355-01 Standard Test Method for Shock-Absorbing Properties of Playing Surface Systems and Materials
• 1995 ASTM F355-95 Standard Test Method for Shock-Absorbing Properties of Playing Surface Systems and Materials