BS EN 621:2009 Non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, without a fan to assist transportation of combustion air and/or combustion products
This European Standard specifies the requirements and test methods for the safety and efficiency of nondomestic gas-fired air heaters not exceeding a net heat input of 300 kW with (an) atmospheric burner(s) and without a fan to assist the transportation of combustion air and/or flue gases, hereafter referred to as "appliances".
This European Standard applies to Type B11, B41, C11 and C31 appliances intended for use in other than single unit residential dwellings. Provision of the heated air may be by means of ducting or may be directly into the heated space.
This standard does not apply to:
a) appliances intended for use in a single unit residential dwelling;
b) appliances of the condensing type;
c) appliances for outdoor installation;
d) dual purpose air conditioning appliances (heating and cooling);
e) appliances where the air is heated by an intermediate fluid;
f) appliances with forced draught burners;
g) appliances fitted with a manual or automatic means of adjusting the combustion air supply or the
combustion products evacuation (including flue dampers);
h) portable or transportable forced convection appliances;
i) appliances having multiple heating units with a single draught diverter;
j) appliances fitted with more than one flue outlet;
k) appliances that are designed for continuous condensation within the flue system under normal
operating conditions;
l) appliances having combustion products evacuation ducts, POCEDs, that are non-metallic.
This standard is applicable to appliances which are intended to be type tested. It also includes requirements concerning the evaluation of conformity, including factory production control, but these requirements only apply to POCEDs and their associated terminals.
NOTE Requirements for appliances which are not type tested would need to be subject to further consideration.
BS EN 621:2009 Referenced Document
EN 10226-1 Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads; Dimensions, tolerances and designation
EN 10226-2 Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation
EN 125 Flame supervision devices for gas burning appliances - Thermoelectric flame supervision devices*, 2022-10-12 Update
EN 126 Multifunctional controls for gas burning appliances*, 2014-11-01 Update
EN 161:2007 Automatic shut-off valves for gas burners and gas appliances
EN 1859:2000 Chimneys - Metal Chimneys - Test Methods Incorporating Amendment A1: June 2006
EN 257 Mechanical thermostats for gas-burning appliances*, 2023-12-13 Update
EN 298:2003 Automatic gas burner control systems for gas burners and gas burning appliances with or without fans
EN 437:2003 Test gases - Test pressures - Appliance categories (Incorporates Amendment A1: 2009)
EN 60335-1 Household and similar electrical appliances - Safety - Part 1: General requirements*, 2018-11-01 Update
EN 60529:1991 Degrees of Protection Provided by Enclosures (IP Code) (Incorporates Amendments A1: 2000 and A2: 2013)
EN 60584-1 Thermocouples - Part 1: EMF specifications and tolerances*, 2024-04-19 Update
EN 60584-2:1993 Thermocouples Part 2: Tolerances (Remains Current)
EN 60730-1 Automatic electrical controls - Part 1: General requirements*, 2016-07-01 Update
EN 60730-2-9:2002 Automatic Electrical Controls for Household and Similar Use Part 2-9: Particular Requirements for Temperature Sensing Controls
EN 61058-1 Switches for appliances Part 1: General requirements (Incorporates Amendment A2: 2008)
EN 88-1 Safety and control devices for gas burners and gas burning appliances - Part 1: Pressure regulators for inlet pressures up to and including 50 kPa*, 2023-12-13 Update
EN ISO 228-1 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation ISO 228-1: 2000
ISO ISO IEC 27001-2013 cor2-2015 technical errata*, 2024-04-19 Update
ISO 1182 Reaction to fire tests for products — Non-combustibility test*, 2020-06-04 Update
ISO 7005-1 Pipe flanges - Part 1: Steel flanges for industrial and general service piping systems*, 2011-07-01 Update
ISO 7005-2 Metallic flanges; part 2: cast iron flanges
BS EN 621:2009 history
2010BS EN 621:2010 Non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, without a fan to assist transportation of combustion air and/or combustion products
2010BS EN 621:2009 Non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, without a fan to assist transportation of combustion air and/or combustion products