BS EN 1915-2:2001+A1:2009
Aircraft ground support equipment — General requirements — Part 2: Stability and strength requirements, calculations and test methods

Standard No.

BS EN 1915-2:2001+A1:2009

Release Date

2001

Published By

British Standards Institution (BSI)

Latest

BS EN 1915-2:2001+A1:2009

Replace

BS EN 1915-2:2001 95/709563 DC-1995

Scope

This Part of EN 1915 specifies the conditions to be taken into consideration when calculating the strength and the stability of GSE according to !EN 1915-1" and the EN 12312 series under intended use conditions. It also specifies general test methods. NOTE The methods given in this standard demonstrate one way of achieving an acceptable safety level. Methods that produce comparable results may be used. This Part of EN 1915 does not establish additional requirements for the following:  operation elsewhere than in an airport environment; operation in severe conditions, e.g. ambient temperature below -20 °C or over 50 °C, tropical or saturated salty atmospheric environment;  hazards caused by wind velocity in excess of the figures given in this European Standard;  earthquake, flood, landslide, lightning and more generally any natural catastrophe. This Part of EN 1915 is not applicable to GSE which are manufactured before the date of publication by CEN of this Standard.

BS EN 1915-2:2001+A1:2009 Referenced Document

• EN 12312 Aircraft ground support equipment - Specific requirements - Part 9: Container/Pallet loaders*， 2013-01-01 Update
• EN 1915-1:2001 Aircraft ground support equipment - General requirements - Part 1: Basic safety requirements Incorporates Amendment A1: 2009
• EN 1915-3 Aircraft ground support equipment - General requirements - Part 3: Vibration measurement methods and reduction*， 2009-03-01 Update
• EN 1915-4 Aircraft ground support equipment - General requirements - Part 4: Noise measurement methods and reduction*， 2009-04-01 Update
• EN ISO 12100-1:2003 Safety of machinery - Basic concepts, general principles for design - Part 1: Basic terminology, methodology Incorporates Amendment A1: 2009 [Superseded: CEN EN 292-1]*， 2024-04-19 Update
• EN ISO 12100-2:2003 Safety of machinery - Basic concepts, general principles for design - Part 2: Technical principles Incorporates Amendment A1: 2009 [Superseded: CEN EN 292-2]*， 2024-04-19 Update
• EN ISO 3834-1 Quality requirements for fusion welding of metallic materials - Part 1: Criteria for the selection of the appropriate level of quality requirements (ISO 3834-1:2021)*， 2021-08-31 Update
• EN ISO 3834-2 Quality requirements for fusion welding of metallic materials - Part 2: Comprehensive quality requirements (ISO 3834-2:2021)*， 2021-03-31 Update
• EN ISO 3834-3 Quality requirements for fusion welding of metallic materials - Part 3: Standard quality requirements (ISO 3834-3:2021)*， 2021-03-31 Update
• EN ISO 3834-4 Quality requirements for fusion welding of metallic materials - Part 4: Elementary quality requirements (ISO 3834-4:2021)*， 2021-04-28 Update
• EN ISO 5817 Welding - Fusion-welded joints in steel, nickel, titanium and their alloys (beam welding excluded) - Quality levels for imperfections (ISO 5817:2023)*， 2023-03-15 Update
• ISO 2408 Steel wire ropes - Requirements*， 2017-06-01 Update
• ISO 8625-1:1993 Aerospace; fluid systems; vocabulary; part 1: general terms and definitions relating to pressure

BS EN 1915-2:2001+A1:2009 history

• 2001 BS EN 1915-2:2001+A1:2009 Aircraft ground support equipment — General requirements — Part 2: Stability and strength requirements, calculations and test methods
• 0000 BS EN 1915-2:2001