ISO 10467:2004
Plastics piping systems for pressure and non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
- Standard No.
- ISO 10467:2004
- Release Date
- 2004
- Published By
- International Organization for Standardization (ISO)
- Status
- Replace By
- ISO 10467:2004/Amd 1:2012
- Latest
- ISO 10467:2018
- Scope
- This International Standard specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) for drainage or sewerage with or without pressure, as well as the properties of the system itself. This International Standard is applicable to GRP-UP piping systems, with flexible or rigid joints with or without end thrust load-bearing capability, primarily intended for use in buried installations. NOTE Piping systems conforming to this International Standard can also be used for non-buried applications provided the influence of the environment and the supports are considered in the design of the pipes, fittings and joints. This International Standard is applicable to pipes, fittings and their joints of nominal sizes from DN 50 to DN 4000 which are intended to be used for the conveyance of drainage or sewerage at temperatures up to 50 °C, with or without pressure. In a pipework system, pipes and fittings of different nominal pressure and stiffness ratings may be used together. Clause 4 specifies the general aspects of GRP-UP piping systems intended to be used in the field of drainage or sewerage with or without pressure. Clause 5 specifies the characteristics of pipes made from GRP-UP with or without aggregates and/or fillers. The pipes may have a thermoplastics or thermosetting resin liner. Clause 5 also specifies the test parameters for the test methods referred to in this International Standard. Clause 6 specifies the characteristics of fittings made from GRP-UP, with or without a thermoplastics or thermosetting resin liner, intended to be used in the field of drainage or sewerage. Clause 6 specifies the dimensional and performance requirements for bends, branches, reducers, saddles and flanged adaptors. Clause 6 is applicable to fittings made using any of the following techniques: a) fabrication from straight pipes; b) moulding by 1) filament winding, 2) tape winding, 3) contact moulding, 4) hot or cold compression moulding.
ISO 10467:2004 Referenced Document
- EN 681-1 Elastomeric seals Material requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber (Incorporates Amendments A1: 1998 and A2: 2002; Incorporating Corrigendum August 2002; Incorporates Amendment A3: 2005)
- EN 681-2 Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers
- ISO 10466 Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection*， 2021-03-31 Update
- ISO 10468 Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the ring creep properties under wet or dry conditions*， 2023-07-01 Update
- ISO 10471 Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the long-term ultimate bending strain and the long-term ultimate relative ring deflection under wet conditions*， 2018-05-01 Update
- ISO 10928:1997 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Methods for regression analysis and their use
- ISO 10952 Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Determination of the resistance to chemical attack for the inside of a section in a deflected condition*， 2021-03-01 Update
- ISO 11922-1 Thermoplastics pipes for the conveyance of fluids - Dimensions and tolerances - Part 1: Metric series*， 2017-12-31 Update
- ISO 14828 Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the long-term specific ring relaxation stiffness under wet conditions and calculation of the wet relaxation factor; Amendment 1*， 2010-09-01 Update
- ISO 15306 Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the resistance to cyclic internal pressure AMENDMENT 1
- ISO 161-1 Thermoplastics pipes for the conveyance of fluids — Nominal outside diameters and nominal pressures — Part 1: Metric series — Amendment 1*， 2023-04-01 Update
- ISO 2078 Textile glass — Yarns — Designation*， 2022-03-16 Update
- ISO 2531 Ductile iron pipes, fittings, accessories and their joints for water applications; Technical Corrigendum 1*， 2010-11-15 Update
- ISO 3126 Plastics piping systems - Plastics components - Determination of dimensions*， 2005-03-01 Update
- ISO 4200 Plain end steel tubes, welded and seamless; general tables of dimensions and masses per unit length
- ISO 527-4 Plastics — Determination of tensile properties — Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites*， 2023-03-24 Update
- ISO 527-5 Plastics — Determination of tensile properties — Part 5: Test conditions for unidirectional fibre-reinforced plastic composites*， 2021-11-24 Update
- ISO 7432:2002 Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals
- ISO 7509 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of time to failure under sustained internal pressure*， 2015-03-01 Update
- ISO 7511:1999 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the leaktightness of the wall under short-term internal pressure
- ISO 7685 Glass-reinforced thermosetting plastics (GRP) pipes — Determination of initial ring stiffness*， 2019-07-11 Update
- ISO 8483:2003 Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the design of bolted flange joints
- ISO 8513:2000 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of longitudinal tensile properties
- ISO 8521:1998 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the apparent initial circumferential tensile strength
- ISO 8533:2003 Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the design of cemented or wrapped joints
- ISO 8639:2000 Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness of flexible joints
- ISO/TR 10465-3 Underground installation of flexible glass-reinforced pipes based on unsaturated polyester resin (GRP-UP) - Part 3: Installation parameters and application limits*， 2007-09-01 Update
- JIS A 5350 Fiberglass reinforced plastic mortar pipes
ISO 10467:2004 history
- 2018 ISO 10467:2018 Plastics piping systems for pressure and non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
- 2012 ISO 10467:2004/Amd 1:2012 Plastics piping systems for pressure and non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin; Amendment 1
- 2004 ISO 10467:2004 Plastics piping systems for pressure and non-pressure drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin
