ASTM F2619/F2619M-07
Standard Specification for High-Density Polyethylene (PE) Line Pipe

Standard No.
ASTM F2619/F2619M-07
Release Date
2007
Published By
American Society for Testing and Materials (ASTM)
Status
Replace By
ASTM F2619/F2619M-11
Latest
ASTM F2619/F2619M-20
Scope

1.1 This specification covers requirements and test methods for high-density polyethylene (PE) materials, pipe and fittings for pressure or non-pressure oil and gas producing applications to convey fluids such as oil, dry or wet gas, multiphase fluids, and non-potable oilfield water. This specification does not cover pipe for gas distribution applications.

1.1.1 For the purposes of this specification, high-density polyethylene material is Specification D 3350 density cell classification 3 or higher. This specification does not cover materials having Specification D 3350 density cell classification less than 3 such as medium or low density polyethylene materials.

1.2 Units8212;The values stated in either SI or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of each other. Combining values from the two systems may result in non-compliance with the standard. Values in parentheses are provided for information only.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ASTM F2619/F2619M-07 Referenced Document

  • ASTM D1598 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure
  • ASTM D1599 Standard Test Method for Resistance to Short-Time Hydraulic Failure Pressure of Plastic Pipe, Tubing, and Fittings
  • ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
  • ASTM D1603 Standard Test Method for Carbon Black In Olefin Plastics
  • ASTM D2122 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings
  • ASTM D2290 Standard Test Method for Apparent Hoop Tensile Strength of Plastic or Reinforced Plastic Pipe
  • ASTM D2683 Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
  • ASTM D2837 Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials
  • ASTM D3261 Standard Specification for Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing
  • ASTM D3350 Standard Specification for Polyethylene Plastics Pipe and Fittings Materials*， 2024-04-19 Update
  • ASTM D4218 Standard Test Method for Determination of Carbon Black Content in Polyethylene Compounds By the Muffle-Furnace Technique
  • ASTM D638 Standard Test Method for Tensile Properties of Plastics
  • ASTM F1055 Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene Pipe and Tubing
  • ASTM F1473 Standard Test Method for Notch Tensile Test to Measure the Resistance to Slow Crack Growth of Polyethylene Pipes and Resins
  • ASTM F1973 Standard Specification for Factory Assebled Anodeless Risers and Transition Fittings in Polyethylene (PE) Fuel Gas Distribution Systems
  • ASTM F2206 Standard Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE)
  • ASTM F412 Standard Terminology Relating to Plastic Piping Systems
  • CSA Z662 Oil and gas pipeline systems

ASTM F2619/F2619M-07 history

Standard Specification for High-Density Polyethylene (PE) Line Pipe


Copyright ©2024 All Rights Reserved