ASTM D6419-00(2005)
Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks
- Standard No.
- ASTM D6419-00(2005)
- Release Date
- 2000
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D6419-00(2009)
- Latest
- ASTM D6419-00(2023)
- Scope
This test method is the procedure of choice for determining volatile content of sheet-fed and coldset web offset inks. This information is useful to the ink manufacturer and user and to environmental interests as part of the determination of the mass of volatile organic compounds emitted from the ink.
Note 38212;Since these inks do not contain water or any materials currently classified by US EPA as negligibly photochemically reactive (exempt solvents), volatile organic compound content is the same as volatile content. The volatile organic compounds in these inks are high boiling hydrocarbon oils which are, according to US EPA guidelines, 95 % retained in the printed substrate or oxidized into the ink film. Therefore, the mass of volatile organic compound emitted from the ink would be calculated as only 5 % of the volatile organic compound content of the ink as derived from the results of this test method.
1.1 This test method describes a procedure for determination of the weight percent volatile content of sheet-fed and coldset web offset printing inks. Test specimens are heated at 110 1C for 60 min.
Note 18212;Coldset web offset printing is often (also) referred to as non-heatset web offset printing.
1.2 This test method is also applicable to sheet-fed and coldset web offset printing ink vehicles.
Note 28212;Vehicle is the liquid portion of the printing ink. Any substance that is dissolved in the liquid portion of the ink is a part of the vehicle.
1.3 This test method is not applicable to ultra-violet (UV) or electron beam cured materials, which must be cured by exposure to UV light or an electron beam as part of the test for volatile content.
1.4 This test method is based on Test Method D 2369, in which the allowable ranges are 177;0.1g for specimen weight and 177;5176;C for oven temperature. Interlaboratory studies have shown that specimen weight and oven temperature must both be more tightly controlled in order to improve the precision of test results for sheet-fed and coldset web-offset inks. Such inks typically contain a wide range of high-boiling hydrocarbons and often have a volatile content below 25 %.
1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For a specific hazard statement see 7.5.1.
ASTM D6419-00(2005) Referenced Document
- ASTM D2369 Standard Test Method for Volatile Content of Coatings
- ASTM D362 Standard Specification for Industrial Grade Toluene
- ASTM E145 Standard Specification for Gravity-Convection And Forced-Ventilation Ovens
- ASTM E691 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM D6419-00(2005) history
- 2023 ASTM D6419-00(2023) Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks
- 2000 ASTM D6419-00(2017) Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks
- 2000 ASTM D6419-00(2009) Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks
- 2000 ASTM D6419-00(2005) Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks
- 2000 ASTM D6419-00 Standard Test Method for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks
- 2000 ASTM D6419-99 Test Method for Volatile Content of Non-Heatset Web Offset Printing Inks
