ASTM D4327-03
Standard Test Method for Anions in Water by Chemically Suppressed Ion Chromatography

Standard No.

ASTM D4327-03

Release Date

2003

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM D4327-11

Latest

ASTM D4327-17

Scope

Ion chromatography provides for both qualitative and quantitative determination of seven common anions, F⁻, Cl⁻, NO₂⁻, HPO₄⁻², Br⁻, NO₃⁻, and SO₄⁻², in the milligram per litre range from a single analytical operation requiring only a few millilitres of sample and taking approximately 10 to 15 min for completion.

Note 28212;This test method may be used to determine fluoride if its peak is in the water dip by adding one mL of eluent (at 100× the concentration in 8.3) to all 100-mL volumes of samples and standards to negate the effect of the water dip. (See 6.3, and also see 6.4.) The quantitation of unretained peaks should be avoided. Anions such as low molecular weight organic acids (formate, acetate, propionate, etc.) that are conductive coelute with fluoride and would bias fluoride quantitation in some drinking waters and most wastewaters.

Anion combinations such as Cl⁻/Br⁻ and NO₂⁻/NO₃⁻, which may be difficult to distinguish by other analytical methods, are readily separated by ion chromatography.

1.1 This test method covers the sequential determination of fluoride, chloride, nitrite, ortho-phosphate, bromide, nitrate, and sulfate ions in water by chemically suppressed ion chromatography. Note 1Order of elution is dependent upon the column used; see .

1.2 This test method is applicable to drinking and wastewaters. The ranges tested for this test method for each anion were as follows (measured in mg/L):

	Fluoride	0.26 to 8.49
	Chloride	0.78 to 26.0
	Nitrite-N	0.36 to 12.0
	Bromide	0.63 to 21.0
	Nitrate-N	0.42 to 14.0
	o-Phosphate	0.69 to 23.1
	Sulfate	2.85 to 95.0

1.3 It is the user''s responsibility to ensure the validity of this test method for other matrices.

1.4 Concentrations as low as 0.01 mg/L were determined depending upon the anions to be quantitated, in single laboratory work. Utilizing a 50-956;L sample volume loop and a sensitivity of 3 956;S/cm full scale, the approximate detection limits shown in Table 1 can be achieved. If lower detection levels are required, the sensitivity may be improved by using a lower scale setting (< 3 956;S/cm) or a larger sample injection loop (>100 956;L). The analyst must assure optimum instrument performance to maintain a stable baseline at more sensitive conductivity full-scale settings.

1.5 The upper limit of this test method is dependent upon total anion concentration and may be determined experimentally as described in Annex A1. These limits may be extended by appropriate dilution or by use of a smaller injection volume.

1.6 Using alternate separator column and eluents may permit additional anions such as formate or citrate to be determined. This is not the subject of this test method.

1.7 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the appl......

ASTM D4327-03 Referenced Document

• ASTM D1066 Standard Practice for Sampling Steam
• ASTM D1129 Standard Terminology Relating to Water
• ASTM D1193 Standard Specification for Reagent Water
• ASTM D2777 Standard Practice for Determination of Precision and Bias of Applicable Methods of Committee D-19 on Water
• ASTM D3370 Standard Practices for Sampling Water from Closed Conduits
• ASTM D5810 Standard Guide for Spiking into Aqueous Samples 
• ASTM D5847 Standard Practice for Writing Quality Control Specifications for Standard Test Methods for Water Analysis

ASTM D4327-03 history

• 2017 ASTM D4327-17 Standard Test Method for Anions in Water by Chemically Suppressed Ion Chromatography
• 2011 ASTM D4327-11 Standard Test Method for Anions in Water by Suppressed Ion Chromatography
• 2003 ASTM D4327-03 Standard Test Method for Anions in Water by Chemically Suppressed Ion Chromatography
• 1997 ASTM D4327-97 Standard Test Method for Anions in Water by Chemically Suppressed Ion Chromatography