ASTM D5955-02(2007)
Standard Test Methods for Estimating Contribution of Environmental Tobacco Smoke to Respirable Suspended Particles Based on UVPM and FPM

Standard No.

ASTM D5955-02(2007)

Release Date

2002

Published By

American Society for Testing and Materials (ASTM)

Status

Be replaced

Replace By

ASTM D5955-02(2012)e1

Latest

ASTM D5955-02(2017)e1

Scope

1.1 These test methods pertain to the sampling/analysis of respirable suspended particles (RSP) and the estimation of the RSP fraction attributable to environmental tobacco smoke (ETS). These test methods are based on collection of total RSP on a membrane filter, extracting the collected material in methanol, and measuring total ultraviolet absorbance or fluorescence, or both, of this extract. The corresponding methods of estimation are termed ultraviolet particulate matter (UVPM) and fluorescent particulate matter (FPM), respectively.

1.2 These test methods are compatible with, but do not require the determination of solanesol, which is also used to estimate the contribution of ETS to RSP (see Test Method D 6271).

1.3 The sampling components consist of a preweighed, 1.0-m pore size polytetrafluoroethylene (PTFE) membrane filter in a filter cassette connected on the inlet end to a particle size separating device and, on the outlet end, to a sampling pump. These test methods are applicable to personal and area sampling.

1.4 These test methods are limited in sample duration only by the capacity of the membrane filter (about 2000 g). These test methods have been evaluated up to a 24-h sample duration with a minimum sample duration of at least 1 h.

1.5 Limits of detection (LOD) and quantitation (LOQ) for the UVPM test method at a sampling rate of 2 L/min are, respectively, 2.5 g/m³ and 8.3 g/m³ for a 1-h sample duration and 0.3 g/m³ and 1.0 g/m³ for an 8-h sample duration. The LOD and LOQ for the FPM test method at a sampling rate of 2 L/min are, respectively, 1.4 g/m³ and 4.7 g/m³ for a 1-h sample duration and 0.2 g/m³ and 0.6 g/m ³ for an 8-h sample duration.

1.6 The values stated in SI units are to be regarded as standard.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary information is given in 13.6.

ASTM D5955-02(2007) Referenced Document

• ASTM D1356 Standard Terminology Relating to Sampling and Analysis of Atmospheres*， 2024-04-19 Update
• ASTM D1357 Standard Practice for Planning the Sampling of the Ambient Atmosphere
• ASTM D3631 Standard Test Methods for Measuring Surface Atmospheric Pressure
• ASTM D5337 Standard Practice for Flow Rate for Calibration of Personal Sampling Pumps
• ASTM D6271 Standard Test Method for Estimating Contribution of Environmental Tobacco Smoke to Respirable Suspended Particles Based on Solanesol

ASTM D5955-02(2007) history

• 1970 ASTM D5955-02(2017)e1 Standard Test Methods for Estimating Contribution of Environmental Tobacco Smoke to Respirable Suspended Particles Based on UVPM and FPM
• 2002 ASTM D5955-02(2012)e1 Standard Test Methods for Estimating Contribution of Environmental Tobacco Smoke to Respirable Suspended Particles Based on UVPM and FPM
• 2002 ASTM D5955-02(2007) Standard Test Methods for Estimating Contribution of Environmental Tobacco Smoke to Respirable Suspended Particles Based on UVPM and FPM
• 2002 ASTM D5955-02 Standard Test Methods for Estimating Contribution of Environmental Tobacco Smoke to Respirable Suspended Particles Based on UVPM and FPM
• 1996 ASTM D5955-96 Standard Test Methods for Estimating Contribution of Environmental Tobacco Smoke to Respirable Suspended Particles Based on UVPM and FPM