DIN EN ISO 1873-2:2007
Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1873-2:2007); English version of DIN EN ISO 1873-2:2007-11

Standard No.

DIN EN ISO 1873-2:2007

Release Date

2007

Published By

German Institute for Standardization

Status

Be replaced

Replace By

DIN EN ISO 19069-2:2016

Latest

DIN EN ISO 19069-2:2016

Replace

DIN EN ISO 1873-2:2000

Scope

This part of ISO 1873 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of PP moulding and extrusion materials.Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given. Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are given.Properties and test methods which are suitable and necessary to characterize PP moulding and extrusion materials are listed. The properties have been selected from the general test methods in ISO 10350-1.Other test methods in wide use for,or of particular significance to,these moulding and extrusion materials are also included in this part of ISO 1873,as are the disignatory properties specified in Part 1. In order to obtain reproducible and comparable test results,it is necessary to use the methods of preparation and conditioning,the specimen dimensions and the test procedures specified herein.Values determined will not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.

DIN EN ISO 1873-2:2007 Referenced Document

• ISO 10350-1 Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials*， 2017-09-01 Update
• ISO 1133:2005 Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
• ISO 11357-2 Plastics — Differential scanning calorimetry (DSC) — Part 2: Determination of glass transition temperature and step height*， 2020-03-02 Update
• ISO 11357-3 Plastics - Differential scanning calorimetry (DSC) - Part 3: Determination of temperature and enthalpy of melting and crystallization*， 2018-03-01 Update
• ISO 11359 Plastics — Thermomechanical analysis (TMA) — Part 3: Determination of penetration temperature*， 2019-02-05 Update
• ISO 1183-1 Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pycnometer method and titration method*， 2019-02-28 Update
• ISO 1183-2 Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method*， 2019-02-28 Update
• ISO 1183-3 Plastics - Methods for determining the density of non-cellular plastics - Part 3: Gas pyknometer method
• ISO 1628-3 Plastics - Determination of the viscosity of polymers in dilute solution using capillary viscometers - Part 3: Polyethylenes and polypropylenes*， 2010-05-01 Update
• ISO 178 Surface chemical analysis — Secondary ion mass spectrometry — Linearity of intensity scale in single ion counting time-of-flight mass analysers*， 2019-04-01 Update
• ISO 179-1 Plastics. Determination of Charpy impact properties - Non-instrumented impact test*， 2023-06-07 Update
• ISO 179-2 Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test — Amendment 1: Precision data*， 2020-05-14 Update
• ISO 2818 Plastics — Preparation of test specimens by machining*， 2018-12-13 Update
• ISO 293 Plastics — Compression moulding of test specimens of thermoplastic materials*， 2023-02-21 Update
• ISO 294-1 Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens*， 2017-05-01 Update
• ISO 294-3 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates*， 2020-06-26 Update
• ISO 294-4 Milling cutters mounted on centring arbors having a 7/24 taper; Fitting dimensions; Centring arbors*， 2018-12-20 Update
• ISO 3167 Plastics - Multipurpose test specimens*， 2014-08-01 Update
• ISO 4589-2 Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test*， 2017-04-01 Update
• ISO 527-2 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics*， 2012-02-01 Update
• ISO 62 Plastics - Determination of water absorption*， 2008-02-01 Update
• ISO 6603-2 Plastics. Determination of puncture impact behaviour of rigid plastics. - Part 2: Instrumented impact testing*， 2023-06-02 Update
• ISO 75-2 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite*， 2013-04-01 Update
• ISO 8256 Plastics*， 2023-11-01 Update
• ISO 899-1 Plastics - Determination of creep behaviour - Part 1: Tensile creep*， 2017-09-01 Update

DIN EN ISO 1873-2:2007 history

• 2016 DIN EN ISO 19069-2:2016 Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19069-2:2016); German version EN ISO 19069-2:2016
• 2007 DIN EN ISO 1873-2:2007 Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1873-2:2007); English version of DIN EN ISO 1873-2:2007-11
• 0000 DIN EN ISO 1873-2:2000

DIN EN ISO 1873-2:2007 Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1873-2:2007); English version of DIN EN ISO 1873-2:2007-11 was changed to DIN EN ISO 19069-2:2016 Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19069-2:2016); German version EN ISO 19069-2:2016.