ISO 10931:2005
Plastics piping systems for industrial applications - Poly(vinylidene fluoride) (PVDF) - Specifications for components and the system

Standard No.

ISO 10931:2005

Release Date

2005

Published By

International Organization for Standardization (ISO)

Status

Be replaced

Replace By

ISO 10931:2005/Amd 1:2015

Latest

ISO 10931:2005/Amd 1:2015

Scope

This International Standard specifies the characteristics and requirements for components such as pipes, fittings and valves made from poly (vinylidene fluoride) (PVDF), intended to be used for thermoplastics piping systems in the field of industrial applications above-ground. It is applicable to PVDF pipes, fittings, valves and ancillary equipment, their joints and to joints with components of other plastics and non-plastics materials, depending on their suitability, intended to be used for the conveyance of liquid and gaseous fluids as well as of solid matters in fluids for industrial applications including ⎯ chemical plants, ⎯ industrial sewerage engineering, ⎯ power engineering (cooling and general purpose water), ⎯ electroplating and pickling plants, ⎯ semiconductor industry, ⎯ agricultural production plants, and ⎯ water treatment. This International Standard is applicable to PVDF piping systems for use at temperatures up to 150 °C. However, for applications above 120 °C, which depend upon the crystalline melting point of the PVDF material, it is advisable to seek the advice of the manufacturer of the component (the components have to withstand the mechanical, thermal and chemical demands to be expected and to be resistant to the fluids to be conveyed). Characteristics and requirements which are applicable for PVDF in general are covered by the relevant clauses of this International Standard. Those characteristics and requirements which depend on the material used are given in Annex A.

ISO 10931:2005 Referenced Document

• IEC 60364-1 Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions; Corrigendum 1*， 2009-08-01 Update
• IEC 60529 Degrees of Protection Provided by Enclosures (IP Code) (Edition 2.1 ***Applies to French text only***)*， 2024-04-18 Update
• ISO 1043-1 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics AMENDMENT 1: New symbol ST for syndiotactic*， 2011-01-01 Update
• ISO 11357-3 Plastics - Differential scanning calorimetry (DSC) - Part 3: Determination of temperature and enthalpy of melting and crystallization*， 2018-03-01 Update
• ISO 1167:1996 Thermoplastics pipes for the conveyance of fluids - Resistance to internal pressure - Test method
• ISO 1183-2 Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method*， 2019-02-28 Update
• ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids - Dimensions and tolerances - Part 1: Metric series
• ISO 12092:2000 Fittings, valves and other piping system components made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C), acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) for pipes under pressure - R
• ISO 12162:1995 Thermoplastics materials for pipes and fittings for pressure applications - Classification and designation - Overall service (design) coefficient
• ISO 15853:1999 Thermoplastic materials - Preparation of tubular test pieces for the determination of the hydrostatic strength of materials used for injection moulding
• ISO 16135 Industrial valves — Ball valves of thermoplastics materials AMENDMENT 1*， 2006-01-01 Update
• ISO 16136 Industrial valves — Butterfly valves of thermoplastics materials AMENDMENT 1*， 2006-01-01 Update
• ISO 16137 Industrial valves — Check valves of thermoplastics materials AMENDMENT 1*， 2006-01-01 Update
• ISO 16138 Industrial valves — Diaphragm valves of thermoplastics materials AMENDMENT 1*， 2006-01-01 Update
• ISO 16139 Industrial valves — Gate valves of thermoplastics materials AMENDMENT 1*， 2006-01-01 Update
• ISO 21787 Industrial valves — Globe valves of thermoplastics materials AMENDMENT 1*， 2006-01-01 Update
• ISO 228-1 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation
• ISO 2505-1:1994 Thermoplastics pipes - Longitudinal reversion - Part 1: Determination methods
• ISO 2505-2:1994 Thermoplastics pipes - Longitudinal reversion - Part 2: Determination parameters
• ISO 265-1 Pipes and fittings of plastics materials; fittings for domestic and industrial waste pipes; basic dimensions: metric series; part 1: unplasticized poly(vinyl chloride) (PVC-U)
• ISO 3126 Plastics piping systems - Plastics components - Determination of dimensions
• ISO 4065 Thermoplastics pipes - Universal wall thickness table*， 2018-01-01 Update
• ISO 472 Plastics — Vocabulary — Amendment 1: Additional items*， 2018-10-31 Update
• ISO 7-1 Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions, tolerances and designation TECHNICAL CORRIGENDUM 1
• ISO 9080:2003 Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
• ISO/TR 10358 Plastics pipes and fittings for industrial applications - Collection of data on combined chemical-resistance*， 2021-05-31 Update

ISO 10931:2005 history

• 2015 ISO 10931:2005/Amd 1:2015 Plastics piping systems for industrial applications - Poly(vinylidene fluoride) (PVDF) - Specifications for components and the system; Amendment 1
• 2005 ISO 10931:2005 Plastics piping systems for industrial applications - Poly(vinylidene fluoride) (PVDF) - Specifications for components and the system