BS EN ISO 11201:1996 Acoustics - Noise emitted by machinery and equipment - Measurement of emission sound pressure levels at a work station and at other specified positions - Engineering method in an essentially free field over a reflecting plane
1 General
This International Standard specifies a method for measuring the emission sound pressure levels of machinery and equipment, at a work station and at other specified positions nearby, in an essentially free field over a reflecting plane. A work station is occu-pied by an operator. It may be located in open space in the room where the source operates, or in a cab fixed to the source, or in an enclosure remote from the source. One or more specified positions may be located in the vicinity of a work station, or in the vi-cinity of an unattended machine. As some of these positions may be occupied occasionally or regularly, they are sometimes referred to as bystander pos-itions.
Emission sound pressure levels are measured as A-weighted and, if required, C-weighted peak, and in frequency bands.
NOTE 1 The contents of this and related International Standards are summarized in table 1 of ISO 11200:1995.
This International Standard specifies requirements for the engineering grade of accuracy on the test en-vironment and instrumentation. Corrections are ap-plied for background noise, but not for the acoustic environment. Instructions are given for the installation and operation of the machine under test and for the choice of microphone positions for the work station and for other specified positions. The purpose of the measurements is to permit comparison of the per-
formance of different units of a given family of ma-chinery or equipment, under defined environmental conditions and standardized mounting and operating conditions. The data obtained may also be used for the declaration and verification of emission sound pressure levels as specified in ISO 4871.
NOTE 2 At any given position in relation to a particular machine, and for given mounting and operating conditions, the emission sound pressure levels determined by the method of this International Standard will in general be lower than the directly measured sound pressure levels for the same machine in the typical workroom where it is used. This is due to reverberation and the contributions of other machines. A method of calculating the sound pressure lev-els in the vicinity of a machine operating alone in a workroom is given in ISO 11690-3. Commonly observed differences are 1 dB to 5 dB, but in extreme cases the dif-ference may be even greater.
2 Types of noise and noise sources
The method specified in this International Standard is applicable to all types of machinery, both moving and stationary, for indoor or outdoor use.
The method is applicable to machines of all sizes, and to all types of noise as defined in ISO 2204 and ISO 12001.
3 Test environment
The type of test environment influences the accuracy of the determination of emission sound pressure lev-els. An essentially free field over a reflecting plane (indoors or outdoors) is required.
4 Specified positions
This International Standard is applicable to work stations and other specified positions where emission sound pressure levels are to be measured.
Examples of appropriate positions where measure-ments may be made include the following:
a) work station located in the vicinity of the machine under test; this is the case for many industrial machines and domestic appliances;
b) work station within a cab which is an integral part of the machine under test; this is the case for many industrial trucks and earth-moving ma-chines;
c) work station within a partial or total enclosure (or behind a screen) supplied by the manufacturer as an integral part of the machinery or equipment;
d) work station partially or totally enclosed by the machine under test; this situation may be en-countered with some large industrial machines;
e) bystander positions occupied by individuals not responsible for the operation of the machine under test, but who may be in its immediate vi-cinity, either occasionally or continuously;
f) other specified positions, not necessarily work stations or bystander positions
BS EN ISO 11201:1996 history
2010BS EN ISO 11201:2010 Acoustics. Noise emitted by machinery and equipment. Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections
0000 BS EN ISO 11201:2009
1996BS EN ISO 11201:1996 Acoustics - Noise emitted by machinery and equipment - Measurement of emission sound pressure levels at a work station and at other specified positions - Engineering method in an essentially free field over a reflecting plane