ASTM D3935-15
Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material
- Standard No.
- ASTM D3935-15
- Release Date
- 2015
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D3935-21
- Latest
- ASTM D3935-21
- Scope
1.1 This classification system covers unfilled and reinforced polycarbonate and polycarbonate copolymer materials suitable for injection molding, blow molding, and extrusion. Some of these compositions may also find use for compression molding or application from solution. This classification system allows for the use of recycled materials provided that all specification requirements are met.
1.2 The properties in this classification system are those required for identifying the compositions covered. Other requirements necessary for identifying particular characteristics important to specific applications are normally specified by using the suffixes in accordance with Section 5.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection should be made by those having expertise in the plastic field only after consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered in this standard.
Note 1: This classification system and ISO8201;7391-1 and ISO8201;7391-2 address the same subject matter, but differ in technical content.
1.5 The following precautionary caveat pertains only to the test methods portion, Section 12, of this classification system. This standard does not purport to address all safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability or regulatory limitations prior to use.
ASTM D3935-15 Referenced Document
- ASTM D1238 Standard Test Method for Flow Rates of Thermoplastics by Extrusion Plastometer
- ASTM D1600 Standard Terminology for Abbreviated Terms Relating to Plastics
- ASTM D256 Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics*， 2023-03-15 Update
- ASTM D2584 Standard Test Method for Ignition Loss of Cured Reinforced Resins
- ASTM D3892 Standard Practice for Packaging/Packing of Plastics
- ASTM D4000 Standard Classification System for Specifying Plastic Materials*， 2023-03-15 Update
- ASTM D5630 Standard Test Method for Ash Content in Thermoplastics
- ASTM D638 Standard Test Method for Tensile Properties of Plastics
- ASTM D648 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position*， 2024-04-22 Update
- ASTM D7209 Standard Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products *， 2024-04-22 Update
- ASTM D790 Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials*， 2024-04-22 Update
- ASTM D792 Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
- ASTM D883 Standard Terminology Relating to Plastics*， 2024-02-01 Update
- ASTM E169 Standard Practices for General Techniques of Ultraviolet-Visible Quantitative Analysis
- ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
- ISO 7391-1 Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 1: Designation system and basis for specifications
- ISO 7391-2 Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties
ASTM D3935-15 history
- 2021 ASTM D3935-21 Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material
- 2015 ASTM D3935-15 Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material
- 2009 ASTM D3935-09 Standard Specification for Polycarbonate (PC) Unfilled and Reinforced Material
- 2002 ASTM D3935-02 Standard Specification for Polycarbonate (PC) Unfilled and Reinforced Material
- 1994 ASTM D3935-94(2001) Standard Specification for Polycarbonate (PC) Unfilled and Reinforced Material
- 1994 ASTM D3935-94 Standard Specification for Polycarbonate (PC) Unfilled and Reinforced Material
