ASTM F1667-17
Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- Standard No.
- ASTM F1667-17
- Release Date
- 2017
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM F1667-18
- Latest
- ASTM F1667/F1667M-21a
- Scope
- 1.1 This specification covers nails, spikes, staples, and other driven fasteners, as listed in Table 1. NOTE 1—Fastener ductility information is presented in Table 2 and dimensional information in Tables 3–65. 1.2 Fasteners described in this specification are driven by hand tool, power tool, or mechanical device in single or multiple strikes and are positioned by hand, tool, or machine. 1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 Fasteners in this specification are sold in bulk (loose) form and are collated for loading into the magazine of an application tool. Other than as covered in Section 9, Workmanship, cohering materials (including, but not limited to, plastic, adhesive bond, paper tape, plastic strip, plastic carrier, wire, etc.) and relative orientation of collated fasteners are not within the scope of this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM F1667-17 Referenced Document
- ASTM A153/A153M Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware*， 2023-05-16 Update
- ASTM A510/A510M Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel*， 2024-04-22 Update
- ASTM A641/A641M Standard Specification for Zinc-Coated (Galvanized) Carbon Steel Wire
- ASTM B695 Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel*， 2021-11-01 Update
- ASTM C514 Standard Specification for Nails for the Application of Gypsum Board
- ASTM F1575 Standard Test Method for Determining Bending Yield Moment of Nails
- ASTM F547 Standard Terminology of Nails for Use with Wood and Wood-Base Materials
- ASTM F592 Standard Terminology of Collated and Cohered Fasteners and Their Application Tools
- ASTM F680 Standard Test Methods for Nails
ASTM F1667-17 history
- 2021 ASTM F1667/F1667M-21a Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2021 ASTM F1667-21 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2020 ASTM F1667-20 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2018 ASTM F1667-18a Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2018 ASTM F1667-18 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2017 ASTM F1667-17 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2015 ASTM F1667-15 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2013 ASTM F1667-13 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2011 ASTM F1667-11ae1 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2011 ASTM F1667-11a Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2011 ASTM F1667-11 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2010 ASTM F1667-10 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2005 ASTM F1667-05 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2003 ASTM F1667-03 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2002 ASTM F1667-02a Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2002 ASTM F1667-02 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2001 ASTM F1667-01a Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2001 ASTM F1667-01 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
- 2000 ASTM F1667-00 Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
