BS EN IEC 62052-11:2021+A11:2022
Electricity metering equipment. General requirements, tests and test conditions - Metering equipment

Standard No.
BS EN IEC 62052-11:2021+A11:2022
Release Date
2023
Published By
British Standards Institution (BSI)
Status
 2024-03
Replace By
BS EN IEC 62052-11:2021+A12:2024
Latest
BS EN IEC 62052-11:2021+A12:2024
Scope
1   Scope This part of IEC 62052 specifies requirements and associated tests, with their appropriate conditions for type testing of AC and DC electricity meters. This document details functional, mechanical, electrical and marking requirements, test methods, and test conditions, including immunity to external influences covering electromagnetic and climatic environments. NOTE 1 For other general requirements, such as safety, dependability, etc., see the relevant IEC 62052 or IEC 62059 standards. For accuracy requirements and other requirements specific to class indices, see the relevant IEC 62053 standards. This document applies to electricity metering equipment designed to: • measure and control electrical energy on electrical networks ( mains ) with voltage up to 1 000 V AC, or 1 500 V DC; NOTE 2 For AC electricity meters, the voltage mentioned above is the line-to-neutral voltage derived from nominal voltages . See IEC 62052‑31:2015, Table 7. NOTE 3 For meters designed for operation with LPITs , only the metering unit is considered a low voltage device. If the LPITs are rated for voltages exceeding 1 000 V AC, or 1 500 V ...

BS EN IEC 62052-11:2021+A11:2022 Referenced Document

  • CISPR 32:2015 Electromagnetic compatibility of multimedia equipment - Emission requirements
  • IEC 60038:2009 IEC standard voltages
  • IEC 60068-2-1:2007 Environmental testing - Part 2-1: Tests - Test A: Cold
  • IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
  • IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
  • IEC 60068-2-30:2005 Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic (12 h + 12 h cycle)
  • IEC 60068-2-5:2018 Environmental testing - Part 2-5: Tests - Test Sa: Simulated solar radiation at ground level and guidance for solar radiation testing and weathering
  • IEC 60068-2-6:2007 Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal)
  • IEC 60381-1:1982 Analogue signals for process control systems. Part 1 : Direct current signals
  • IEC 60404-5:2015 Magnetic Materials - Part 5: Permanent magnet (magnetically hard) materials - Methods of measurement of magnetic properties
  • IEC 60404-8-1:2015 Magnetic materials - Part 8-1: Specifications for individual materials - Magnetically hard materials
  • IEC 60404-8-4:2013 Magnetic materials.Part 8-4: Specifications for individual materials.Cold-rolled non-oriented electrical steel strip and sheet delivered in the fully-processed state
  • IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
  • IEC 60721-1:1990 Classification of environmental conditions; part 1: environmental parameters and their severities
  • IEC 60947-1:2007 Low-voltage switchgear and controlgear - Part 1: General rules
  • IEC 60947-1:2007/AMD1:2010 Low-voltage switchgear and controlgear - Part 1: General rules
  • IEC 60947-1:2007/AMD2:2014 Low-voltage switchgear and controlgear - Part 1: General rules
  • IEC 61000-4-11:2020 Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests for equipment with input current up to 16
  • IEC 61000-4-12:2017 Electromagnetic compatibility (EMC) - Part 4-12: Testing and measurement techniques - Ring wave immunity test
  • IEC 61000-4-18:2019 Electromagnetic compatibility (EMC) - Part 4-18: Testing and measurement techniques - Damped oscillatory wave immunity test
  • IEC 61000-4-19:2014 Electromagnetic Compatibility (EMC) - Part 4-19: Testing and measurement techniques - Test for immunity to conducted, differential mode disturbances and signalling in the frequency range from 2 kHz to 150 kHz, at a.c. power ports
  • IEC 61000-4-20:2010 Electromagnetic compatibility (EMC) - Part 4-20: Testing and measurement techniques - Emission and immunity testing in transverse electromagnetic (TEM) waveguides
  • IEC 61000-4-29:2000 Electromagnetic compatibility (EMC) - Part 4-29: Testing and measurement techniques; Voltage dips, short interruptions and voltage variations on d.c. input power port immunity tests
  • IEC 61000-4-2:2008 Electromagnetic compatibility (EMC) - Part 4-2: Testing and measuring techniques - Electrostatic discharge immunity test
  • IEC 61000-4-3:2006 Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test
  • IEC 61000-4-3:2006/AMD1:2007 Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test; Amendment 1
  • IEC 61000-4-3:2006/AMD2:2010 Electromagnetic compatibility (EMC) - Part 43: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test; Amendment 2
  • IEC 61000-4-4:2012 Electromagnetic compatibility (EMC) - Part 4-4: Testing and measurement techniques - Electrical fast transient/burst immunity test
  • IEC 61000-4-6:2013 Electromagnetic compatibility (EMC) - Part 4-6: Testing and measurement techniques - Immunity to conducted disturbances, induced by radio-frequency fields
  • IEC 61000-4-8:2009 Electromagnetic compatibility (EMC) - Part 4-8: Testing and measurement techniques - Power frequency magnetic field immunity test
  • IEC 61869-3:2011 Instrument transformers - Part 3: Additional requirements for inductive voltage transformers
  • IEC 62052-31:2015 Electricity metering equipment (AC) - General requirements, tests and test conditions - Part 31: Product safety requirements and tests
  • IEC 62054-21:2004 Electricity metering (a.c.) - Tariff and load control - Part 21: Particular requirements for time switches
  • IEC 62056-6-1:2017 Electricity metering data exchange - The DLMS/COSEM suite - Part 6-1: Object Identification System (OBIS)
  • IEC 62056-6-2:2017 Electricity metering data exchange - The DLMS/COSEM suite - Part 6-2: COSEM interface classes
  • IEC 62059-32-1:2011 Electricity Metering Equipment - Dependability - Part 32-1: Durability - Testing of the stability of metrological characteristics by applying elevated temperature

BS EN IEC 62052-11:2021+A11:2022 history

Electricity metering equipment. General requirements, tests and test conditions - Metering equipment


Copyright ©2024 All Rights Reserved