ASTM D5412-93(2017)e1
Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water
- Standard No.
- ASTM D5412-93(2017)e1
- Release Date
- 2011
- Published By
- American Society for Testing and Materials (ASTM)
- Latest
- ASTM D5412-93(2017)e1
- Scope
- 1.1 This test method covers a means for quantifying or characterizing total polycyclic aromatic hydrocarbons (PAHs) by fluorescence spectroscopy (Fl) for waterborne samples. The characterization step is for the purpose of finding an appropriate calibration standard with similar emission and synchronous fluorescence spectra. 1.2 This test method is applicable to PAHs resulting from petroleum oils, fuel oils, creosotes, or industrial organic mixtures. Samples can be weathered or unweathered, but either the same material or appropriately characterized site-specific PAH or petroleum oil calibration standards with similar fluorescence spectra should be chosen. The degree of spectral similarity needed will depend on the desired level of quantification and on the required data quality objectives. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D5412-93(2017)e1 Referenced Document
- ASTM D1129 Standard Terminology Relating to Water
- ASTM D1193 Standard Specification for Reagent Water
- ASTM D2777 Standard Practice for Determination of Precision and Bias of Applicable Methods of Committee D-19 on Water
- ASTM D3325 Standard Practice for Preservation of Waterborne Oil Samples*， 2020-01-01 Update
- ASTM D3326 Standard Practice for Preparation of Samples for Identification of Waterborne Oils
- ASTM D3415 Standard Practice for Identification of Waterborne Oils*， 2017-12-15 Update
- ASTM D3650 Standard Test Method for Comparison of Waterborne Petroleum Oils By Fluorescence Analysis
- ASTM D4489 Standard Practices for Sampling of Waterborne Oils*， 2017-12-15 Update
- ASTM D4657 Standard Test Method for Polynuclear Aromatic Hydrocarbons in Water
- ASTM E131 Standard Definitions of Terms and Symbols Relating to Molecular Spectroscopy
- ASTM E169 Standard Practices for General Techniques of Ultraviolet-Visible Quantitative Analysis
- ASTM E275 Standard Practice for Describing and Measuring Performance of Ultraviolet, Visible, and Near-Infrared Spectrophotometers
- ASTM E388 Standard Test Method for Spectral Bandwidth and Wavelength Accuracy of Fluorescence Spectrometers
- ASTM E578 Standard Test Method for Linearity of Fluorescence Measuring Systems
- ASTM E579 Standard Test Method for Limit of Detection of Fluorescence of Quinine Sulfate
ASTM D5412-93(2017)e1 history
- 2011 ASTM D5412-93(2017)e1 Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water
- 1993 ASTM D5412-93(2011)e1 Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water
- 1993 ASTM D5412-93(2011) Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water
- 1993 ASTM D5412-93(2005) Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water
- 1993 ASTM D5412-93(2000) Standard Test Method for Quantification of Complex Polycyclic Aromatic Hydrocarbon Mixtures or Petroleum Oils in Water
