ASTM E2634-17
Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems
- Standard No.
- ASTM E2634-17
- Release Date
- 2017
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM E2634-18
- Latest
- ASTM E2634-18(2022)
- Scope
- 1.1 This specification is intended to apply to Insulating Concrete Form (ICF) Systems that will act as permanent formwork for cast-in-place reinforced concrete beams; lintels; exterior and interior, above and below grade bearing and non-bearing walls; foundations; and retaining walls. The specification is restricted to ICF Systems with a resultant uniform monolithic concrete core. 1.2 Products covered by the specification consists of molded expanded polystyrene (EPS) insulation panels that are connected by cross ties to form the ICF System. 1.3 This specification identifies test methods appropriate for establishing ICF System performance in their primary function as a stay in place concrete forming system. The use of ICF Systems covered by this specification shall be regulated by building codes that address fire performance, structural performance or both. The fire performance of the material shall be addressed through standard fire test methods established by the appropriate governing documents. The structural performance must be addressed through design of concrete structures in accordance with the appropriate Code requirements. 1.4 Details of manufacturing procedures are beyond the scope of this specification. 1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. For conversion to metric units other than those contained in this specification, refer to IEEE/ASTM SI 10. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM E2634-17 Referenced Document
- ASTM C1002 Standard Specification for Steel Self-Piercing Tapping Screws for Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs*， 2022-06-01 Update
- ASTM C1363 Standard Test Method for the Thermal Performance of Building Assemblies by Means of a Hot Box Apparatus
- ASTM C1396/C1396M Standard Specification for Gypsum Board*， 2024-04-22 Update
- ASTM C203 Standard Test Methods for Breaking Load and Flexural Properties of Block-Type Thermal Insulation
- ASTM C390 Standard Criteria for Sampling and Acceptance of Preformed Thermal Insulation Lots
- ASTM C475/C475M Standard Specification for Joint Compound and Joint Tape for Finishing Gypsum Board*， 2022-06-01 Update
- ASTM C578 Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation
- ASTM C645 Standard Specification for Nonstructural Steel Framing Members*， 2018-06-01 Update
- ASTM D1622/D1622M Standard Test Method for Apparent Density of Rigid Cellular Plastics*， 2024-04-22 Update
- ASTM D1761 Standard Test Methods for Mechanical Fasteners in Wood
- ASTM D1929 Standard Test Method for Determining Ignition Temperature of Plastics
- ASTM D2863 Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-like Combustion of Plastics (Oxygen Index)
- ASTM D635 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position
- ASTM D638 Standard Test Method for Tensile Properties of Plastics
- ASTM D732 Standard Test Method for Shear Strength of Plastics by Punch Tool
- ASTM E119 Standard Test Methods for Fire Tests of Building Construction and Materials
- ASTM E283 Standard Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen
- ASTM E331 Standard Test Method for Water Penetration Of Exterior Windows, Curtain Walls, And Doors By Uniform Static Air Pressure Difference
- ASTM E8/E8M Standard Test Methods for Tension Testing of Metallic Materials*， 2024-01-01 Update
- ASTM E84 Standard Test Method for Surface Burning Characteristics of Building Materials
- ASTM E90 Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements
- IEEE/ASTM SI 10 American National Standard for Metric Practice
ASTM E2634-17 history
- 2022 ASTM E2634-18(2022) Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems
- 2018 ASTM E2634-18 Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems
- 2017 ASTM E2634-17 Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems
- 2016 ASTM E2634-16 Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems
- 2011 ASTM E2634-11(2015) Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems
- 2011 ASTM E2634-11 Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems
- 2010 ASTM E2634-10 Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems
- 2008 ASTM E2634-08 Standard Specification for Flat Wall Insulating Concrete Form (ICF) Systems
