ASTM D5034-09(2017)
Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)
- Standard No.
- ASTM D5034-09(2017)
- Release Date
- 2017
- Published By
- American Society for Testing and Materials (ASTM)
- Status
- Replace By
- ASTM D5034-21
- Latest
- ASTM D5034-21
- Scope
- 1.1 This test method covers the grab and modified grab test procedures for determining the breaking strength and elongation of most textile fabrics. Provisions are made for wet testing. 1.1.1 The grab test procedure is applicable to woven, nonwoven, and felted fabrics, while the modified grab test procedure is used primarily for woven fabrics. 1.2 This test method is not recommended for glass fabrics, or for knitted fabrics and other textile fabrics which have high stretch (more than 11 %). NOTE 1—For the determination of the breaking force and elongation of textile fabrics using the raveled strip test procedure and the cut strip test procedure, refer to Test Method D5035. 1.3 This test method provides the values in both inch-pound units and SI units. Inch-pound units is the technically correct name for the customary units used in the United States. SI units is the technically correct name for the system of metric units known as the International System of Units. The values stated in either acceptable metric units or in other units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining in any way. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D5034-09(2017) Referenced Document
- ASTM D1059 Standard Test Method for Yarn Number Based on Short-Length Specimens
- ASTM D123 Standard Terminology Relating to Textiles
- ASTM D1776 Standard Practice for Conditioning and Testing Textiles
- ASTM D4848 Standard Terminology Related to Force, Deformation and Related Properties of Textiles
- ASTM D4849 Standard Terminology Related to Yarns and Fibers
- ASTM D4850 Standard Terminology Relating to Fabrics and Fabric Test Methods
- ASTM D5035 Standard Test Method for Breaking Force and Elongation of Textile Fabrics (Strip Method)
- ASTM D629 Standard Test Methods for Quantitative Analysis of Textiles
- ASTM D76 Standard Specification for Tensile Testing Machines for Textiles
ASTM D5034-09(2017) history
- 2021 ASTM D5034-21 Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)
- 2017 ASTM D5034-09(2017) Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)
- 2009 ASTM D5034-09(2013) Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)
- 2009 ASTM D5034-09 Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)
- 2008 ASTM D5034-08 Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)
- 1995 ASTM D5034-95(2001) Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)
- 1995 ASTM D5034-95 Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)
